{"title":"3D Print Files","description":"\u003cp\u003eDigital STL files — print your own. Sized to the same precision as the finished organizers.\u003c\/p\u003e","products":[{"product_id":"custom-stl-file-milwaukee-packout-low-profile-organizer-center-blank-insert","title":"Milwaukee Packout 48-22-8431 Center Blank Insert – STL File","description":"\u003cp\u003e\u003cstrong\u003eDesign your own center insert.\u003c\/strong\u003e This is the 3D print file for a blank insert that fills the narrow center section of the Milwaukee Packout 48-22-8431 Low-Profile Organizer. It has two layers: a lower storage tray with an open bin for small tools and hardware, and a blank upper lid you can cut your own tool pockets into. It holds nothing until you customize it.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. The Packout organizer is not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole insert, the storage tray and the lid side by side\u003cbr\u003e\n- \u003cstrong\u003eFour STL files\u003c\/strong\u003e: the same insert pre-split into four pieces (front and back half of the tray, front and back half of the lid), each about 53 × 151 mm, so it prints on a 220 × 220 mm bed. The halves have lock connections, so they slide together securely\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings and print tips\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer), center section\u003c\/p\u003e\n\n\u003cp\u003eSIZE AND PRINTER REQUIREMENTS\u003cbr\u003e\n- Each layer is about 53 × 302 mm; tray and lid stack to about 43.5 mm\u003cbr\u003e\n- The four pieces each fit a 220 × 220 mm bed\u003cbr\u003e\n- \u003cstrong\u003eWant different splits?\u003c\/strong\u003e Your slicer can cut the whole file too. See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003c\/p\u003e\n\n\u003cp\u003eCUSTOMIZING\u003cbr\u003e\nImport the STL into your CAD program or slicer and cut pockets into the lid for your own tools. Need a layout we already make? Message us.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003eLooking for the left- and right-hand pockets? We sell blank inserts for those too. Don't want to design your own? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700071743724,"sku":"MIL-901-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-901-dig-01-blank-insert-render.jpg?v=1792955586"},{"product_id":"custom-stl-step-file-milwaukee-packout-low-profile-organizer-insert-lh","title":"Milwaukee Packout 48-22-8431 Low-Profile Organizer LH Blank Insert – STL\/STEP File","description":"\u003cp\u003e\u003cstrong\u003eDesign your own insert.\u003c\/strong\u003e This is the 3D print and CAD file for a blank insert that fills the left-hand pocket of the Milwaukee Packout 48-22-8431 Low-Profile Organizer (viewed with the hinge away from you). It's a flat, solid 24 mm block shaped to the pocket: cut your own tool or socket pockets into it in CAD, or print it as a spacer.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. The Packout organizer is not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTEP file\u003c\/strong\u003e: the whole insert as an editable solid, the easiest way to cut your own pockets in CAD\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole insert in one piece\u003cbr\u003e\n- \u003cstrong\u003eFour STL files\u003c\/strong\u003e: the same insert pre-split into four corners, each under 165 × 115 mm, so it prints on a 220 × 220 mm bed. The corners have lock connections, so they slide together securely\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings and print tips\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer), left-hand pocket. The right-hand blank is a separate listing in our shop.\u003c\/p\u003e\n\n\u003cp\u003eSIZE AND PRINTER REQUIREMENTS\u003cbr\u003e\n- Whole insert: 318.8 × 213.4 × 24 mm, so one piece needs a bed of about 320 × 215 mm\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed?\u003c\/strong\u003e Print the four corners, which each fit a 220 × 220 mm bed. Or let your slicer cut it: see the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003eDon't want to design your own? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700071874796,"sku":"MIL-902-DIG","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-902-dig-01-blank-insert-render.jpg?v=1792955586"},{"product_id":"custom-stl-file-milwaukee-packout-low-profile-organizer-insert-rh","title":"Milwaukee Packout 48-22-8431 Low-Profile Organizer RH Blank Insert – STL\/STEP File","description":"\u003cp\u003e\u003cstrong\u003eDesign your own insert.\u003c\/strong\u003e This is the 3D print and CAD file for a blank insert that fills the right-hand pocket of the Milwaukee Packout 48-22-8431 Low-Profile Organizer (viewed with the hinge away from you). It's a flat, solid 24 mm block shaped to the pocket: cut your own tool or socket pockets into it in CAD, or print it as a spacer.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. The Packout organizer is not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTEP file\u003c\/strong\u003e: the whole insert as an editable solid, the easiest way to cut your own pockets in CAD\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole insert in one piece\u003cbr\u003e\n- \u003cstrong\u003eFour STL files\u003c\/strong\u003e: the same insert pre-split into four corners, each under 165 × 115 mm, so it prints on a 220 × 220 mm bed. The corners have lock connections, so they slide together securely\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings and print tips\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer), right-hand pocket. The left-hand blank is a separate listing in our shop.\u003c\/p\u003e\n\n\u003cp\u003eSIZE AND PRINTER REQUIREMENTS\u003cbr\u003e\n- Whole insert: 318.8 × 213.4 × 24 mm, so one piece needs a bed of about 320 × 215 mm\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed?\u003c\/strong\u003e Print the four corners, which each fit a 220 × 220 mm bed. Or let your slicer cut it: see the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003eDon't want to design your own? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700071907564,"sku":"MIL-903-DIG","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-903-dig-01-blank-insert-render.jpg?v=1792955586"},{"product_id":"milwaukee-packout-socket-organizer-stl-file-tekton-3-8-metric-socket-tray-shd91211","title":"Milwaukee Packout 3\/8\" Metric 6-Point Socket Organizer STL File – Tekton SHD91211 (38-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Tekton SHD91211 organizer insert for the Milwaukee Packout 48-22-8431: the complete 3\/8\" drive metric 6-point set, standard and deep, every size from 6 mm to 24 mm with no skipped sizes. 38 sockets, every socket size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, tools, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the left-hand and the right-hand version of the organizer, each one piece with the raised size labels in place. The right-hand file mirrors the left, with the labels still reading the right way.\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 320 × 215 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED\u003cbr\u003e\nStandard sockets, 19: 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24 mm (SHD12106–SHD12124)\u003cbr\u003e\nDeep sockets, 19: the same 19 sizes (SHD13106–SHD13124)\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer), in the left-hand or right-hand position. Print the side you need, or print both.\u003cbr\u003e\n✘ Does not fit the 48-22-8430, 48-22-8435 or 48-22-8436.\u003cbr\u003e\nBuilt to the Tekton SHD91211 set. Standard sockets stand upright; deep sockets lie flat in their own troughs.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: the pockets are cut to Tekton SHD91211 3\/8\" metric 6-point sockets. Other brands and sets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Each side prints as one piece, 319 × 213 × 38 mm. Your bed must be at least about 320 × 215 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 or 300 × 300 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints flat, as-is. Designed and tested on a Creality K2 Plus; we print ours in PETG.\u003c\/p\u003e\n\n\u003cp\u003eCOLOR\u003cbr\u003e\n- The file prints in one color as-is: the size labels stand 1 mm proud, so they read in a single color.\u003cbr\u003e\n- Want contrasting labels? Paint the label tops with your slicer's paint tool.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700072071404,"sku":"TEK-004-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/tek-004-dig-01-metric-organizer-render.jpg?v=1792954854"},{"product_id":"milwaukee-packout-socket-organizer-stl-file-tekton-3-8-sae-socket-tray-skt15101","title":"Milwaukee Packout 3\/8\" SAE 6-Point Socket Organizer STL File – Tekton SKT15101 (34-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Tekton SKT15101 organizer insert for the Milwaukee Packout 48-22-8431: the complete 3\/8\" drive SAE 6-point set, standard and deep, 1\/4\"–1\", plus the ratchet, both extensions and the universal joint. 34 pieces, every socket size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, tools, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the left-hand and the right-hand version of the organizer, each one piece with the raised size labels in place. The right-hand file mirrors the left, with the labels still reading the right way.\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 320 × 215 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED\u003cbr\u003e\nStandard sockets, 15: 1\/4\", 9\/32\", 5\/16\", 11\/32\", 3\/8\", 7\/16\", 1\/2\", 9\/16\", 5\/8\", 11\/16\", 3\/4\", 13\/16\", 7\/8\", 15\/16\", 1\" (SHD12006–SHD12025)\u003cbr\u003e\nDeep sockets, 15: the same 15 sizes (SHD13006–SHD13025)\u003cbr\u003e\nDrive tools, 4: 90-tooth quick-release ratchet (SRH11108), 3\" extension (SHA11103), 6\" extension (SHA11106), universal joint (SHA12101)\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer), in the left-hand or right-hand position. Print the side you need, or print both.\u003cbr\u003e\n✘ Does not fit the 48-22-8430, 48-22-8435 or 48-22-8436.\u003cbr\u003e\nBuilt to the Tekton SKT15101 set. Standard sockets stand upright; deep sockets, the ratchet, extensions and universal joint lie flat in their own slots.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: the pockets are cut to Tekton SKT15101 3\/8\" SAE 6-point sockets and tools. Other brands and sets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Each side prints as one piece, 319 × 213 × 38 mm. Your bed must be at least about 320 × 215 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 or 300 × 300 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints flat, as-is. Designed and tested on a Creality K2 Plus; we print ours in PETG.\u003c\/p\u003e\n\n\u003cp\u003eCOLOR\u003cbr\u003e\n- The file prints in one color as-is: the size labels stand 1 mm proud, so they read in a single color.\u003cbr\u003e\n- Want contrasting labels? Paint the label tops with your slicer's paint tool.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700072136940,"sku":"TEK-003-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/tek-003-dig-01-sae-organizer-render.jpg?v=1791499127"},{"product_id":"bauer-modular-drawer-71125-icon-3-8-socket-tray-stl-files-sae-metric-harbor-freight-3d-print-files","title":"Bauer Modular Drawer 71125 3\/8\" Impact Socket Organizer STL File – Icon SAE \u0026 Metric (50-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Icon impact socket organizer for the Bauer 71125 modular drawer: all four Harbor Freight Icon 3\/8\" drive impact sets in one drawer, 50 sockets, SAE and metric, standard and deep, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the organizer as one piece, the same design we print for the finished insert\u003cbr\u003e\n- \u003cstrong\u003eThree STL files\u003c\/strong\u003e: the spacer grid (left, center and right) that lifts the organizer level above the drawer's floor ribs\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: a snap-in drawer label for the label slot on the drawer face\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer)\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSETS COVERED (Icon item numbers)\u003cbr\u003e\n- SAE standard, 12 sockets 5\/16\"–1\": 59750\u003cbr\u003e\n- SAE deep, 12 sockets 5\/16\"–1\": 59739\u003cbr\u003e\n- Metric standard, 13 sockets 7–19 mm: 70432\u003cbr\u003e\n- Metric deep, 13 sockets 7–19 mm: 59756\u003c\/p\u003e\n\n\u003cp\u003eQUICK SCAN\u003cbr\u003e\n- All four Icon 3\/8\" impact sets in one Bauer 71125 drawer\u003cbr\u003e\n- Each labeled column holds the standard socket and its deep partner\u003cbr\u003e\n- Three open bins at the back for extensions and adapters\u003cbr\u003e\n- Print it yourself, in any colors you want\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Bauer modular drawer 71125, both the original drawer and the current one with divider posts on the floor ribs: the organizer sits on the included spacer grid and drops straight in\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Icon's 3\/8\" standard and deep impact sockets. Sockets from another brand, or a different drive, may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The organizer is one piece, 398 × 279 × 25.5 mm, larger than most printer beds, so plan to split it. The spacers are 15 mm tall: 122 × 279 mm (left and right) and 118 × 279 mm (center). The drawer label is about 72 × 24 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print each part as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels are raised above their decks, and the decks sit at three heights, so a single filament change can't colour them.\u003cbr\u003e\n- To print the labels in a second colour, paint the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise the organizer prints in one colour.\u003cbr\u003e\n- The drawer label is made for a second colour on its raised text, and prints fine in one colour too.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700072595692,"sku":"ICN-005-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/icn-005-dig-01-organizer-render.jpg?v=1791565097"},{"product_id":"stl-file-sae-milwaukee-impact-socket-organizer-for-packout-low-profile-3-8-drive-no-skip","title":"Milwaukee Packout 3\/8\" Milwaukee Shockwave SAE 6-Point Impact Socket Organizer STL File – No-Skip Complete Series, Standard \u0026 Deep (1\/4\"–1\")","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert: the complete 3\/8\" drive SAE impact lineup, standard and deep, 6-point, 1\/4\" through 1\", 30 sockets, no skipped sizes, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer)\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 3\/8\" SAE impact sockets, 1\/4\" through 1\" in both standard and deep. The standard sockets stand upright in labeled pockets; the deep sockets lie flat in labeled troughs. A storage compartment holds extras such as an extension, a swivel or an adapter.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 3\/8\" SAE impact sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 37 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- PETG recommended\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The standard-socket size labels are raised 1 mm above the deck. To print them in a second colour, add a filament change at the first layer above 22.1 mm and change back after 23.1 mm.\u003cbr\u003e\n- The deep-socket labels are cut into the troughs, so they print in the body colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700073316588,"sku":"MIL-002-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-002-dig-01-sae-organizer-render.jpg?v=1791563638"},{"product_id":"stl-file-metric-milwaukee-impact-socket-organizer-for-packout-low-profile-3-8-drive-no-skip","title":"Milwaukee Packout 3\/8\" Milwaukee Shockwave Metric 6-Point Impact Socket Organizer STL File – No-Skip Complete Series, Standard \u0026 Deep (6mm–24mm)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert: the complete 3\/8\" drive metric impact lineup, standard and deep, 6-point, 6–24mm, 38 sockets, no skipped sizes, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece, the same design we print for the finished insert\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer)\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 3\/8\" metric impact sockets, 6mm through 24mm in both standard and deep. The standard sockets stand upright in labeled pockets; the deep sockets lie flat in labeled troughs.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 3\/8\" metric impact sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 192 × 33 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The standard-socket size labels and logo are raised 1 mm above the deck. To print them in a second colour, add a filament change at the first layer above 23.3 mm and change back after 24.3 mm.\u003cbr\u003e\n- The deep-socket labels are cut into the troughs, so they print in the body colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700073480428,"sku":"MIL-004-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-004-dig-01-metric-organizer-render.jpg?v=1792944126"},{"product_id":"custom-stl-file-milwaukee-packout-low-profile-organizer-center-section-for-gearwrench-10mm-socket-set","title":"Milwaukee Packout 48-22-8431 Center Socket Organizer STL File – GearWrench 80319 10mm Socket Variety Kit (1\/4\" \u0026 3\/8\" Drive)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout center-compartment insert for the GearWrench 80319 10mm socket set: ten 10mm sockets (standard, mid-length, deep, flex and magnetic, in 1\/4\" and 3\/8\" drive), each in its own pocket, with open storage underneath.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eFour STL files\u003c\/strong\u003e: the socket level and the storage level, each in two halves that key together end to end\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if you ever need to\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer), center compartment\u003cbr\u003e\nBuilt to the GearWrench 80319 10-piece 10mm socket set. The socket level sits on top of the storage level; lift it out to reach the storage underneath, and an opening at one end gives access to a pocket in the level below.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the GearWrench 80319 sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Four parts. Assembled, about 296 × 53 × 44 mm; the largest part is about 151 × 53 mm, so every part fits a 220 × 220 mm bed.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Print each part as it loads, flat side down\u003cbr\u003e\n- PETG recommended\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABEL (optional)\u003cbr\u003e\n- The \"10MM\" mark at the open end of the socket level stands 1.5 mm above the deck. To print it in a second colour, add a filament change on that part at the first layer above 9.5 mm.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003eDon't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":47700073775340,"sku":"GRW-001-DIG","price":12.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/grw-001-dig-01-render.jpg?v=1792954854"},{"product_id":"milwaukee-shockwave-1-2-metric-standard-depth-socket-organizer-stl-file-for-milwaukee-packout-29-piece","title":"Milwaukee Packout 1\/2\" Milwaukee Shockwave Metric Standard-Depth 6-Point Impact Socket Organizer STL File – No-Skip Complete Series (8mm–36mm)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert: the complete 1\/2\" drive metric standard-depth impact lineup, 6-point, 8–36mm, 29 sockets, no skipped sizes, every size labeled. Milwaukee's 49-66-6804 set covers 14 of these sizes (10–22mm and 24mm); the rest are sold individually, and the file has a pocket for every one.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne STL file\u003c\/strong\u003e: the whole organizer as one piece, with the size labels raised on six stepped decks\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Tool chest drawers with at least 58 mm of clear height (the organizer is 57.5 mm tall), no adapter\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Deep Organizer) and 48-22-8435 (Compact Deep Organizer), Packout slim, medium and deep drawers, and the Bauer 71125 drawer, each with the matching Mountaineer Maker spacer or adapter (sold separately)\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 1\/2\" metric standard-depth impact sockets, 8mm through 36mm. Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 1\/2\" metric standard-depth impact sockets. Other brands and deep sockets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 mm and 57.5 mm tall. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels are raised 1 mm. They sit on decks at six different heights, so a single filament change won't catch them all: to print them in a second colour, paint the label tops with your slicer's colour-painting tool.\u003cbr\u003e\n- Printed in one colour, the raised numbers still read clearly.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":48223023825132,"sku":"MIL-001-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-001-dig-01-metric-organizer-render.jpg?v=1792942735"},{"product_id":"milwaukee-packout-3-8-drive-impact-socket-organizer-stl-3mf-file-tekton-sid91211-6-point-metric-shallow-deep-38-pc","title":"Milwaukee Packout 3\/8\" Drive Impact Socket Organizer STL\/3MF File for Tekton SID91211 6-Point Metric, Shallow \u0026 Deep, 6–24mm (38-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Tekton SID91211 organizer insert: the complete 3\/8\" drive metric impact set, shallow and deep, 6-point, 6–24mm, 38 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003e3MF file\u003c\/strong\u003e: the whole organizer with the size labels and logo already in place as separate parts, ready for a two-colour print\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e (base and labels): the same design as two STLs, for slicers that prefer STL\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer)\u003cbr\u003e\nBuilt to the Tekton SID91211 set, with pocket sizes taken from calipers on the actual sockets. Shallow sockets stand upright; deep sockets lie flat in labeled troughs.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Tekton SID91211 3\/8\" metric impact sockets. Other brands and sets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 41 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: every overhang is designed at 45° or steeper\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eOPENING THE 3MF (two colours)\u003cbr\u003e\n- If your slicer asks to \u003cstrong\u003escale to millimeters\u003c\/strong\u003e, answer \u003cstrong\u003eNo\u003c\/strong\u003e. The file is already in millimeters; the small label parts trigger that question.\u003cbr\u003e\n- If it asks to load as \u003cstrong\u003ea single object with multiple parts\u003c\/strong\u003e, answer \u003cstrong\u003eYes\u003c\/strong\u003e. That keeps every label in its recess.\u003cbr\u003e\n- Every part loads on filament 1. Change only the BASE part to your second filament; the labels and logo stay on the first, and that's your two-colour print.\u003cbr\u003e\n- A warning that labels are not on the surface is expected: they sit inside recesses on purpose. The colour changes are banded by depth on purpose to keep them few.\u003cbr\u003e\n- Using the STLs instead? Import both files together without re-arranging, so the labels stay on their pads.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67612006645996,"sku":"TEK-006-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/tek-006-dig-01-metric-organizer-render.jpg?v=1792945105"},{"product_id":"milwaukee-packout-3-8-drive-socket-organizer-stl-file-tekton-shd91211-6-point-metric-shallow-deep-38-pc","title":"Milwaukee Packout 3\/8\" Drive Socket Organizer STL File for Tekton SHD91211 6-Point Metric, Shallow \u0026 Deep, 6–24mm (38-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Tekton SHD91211 organizer insert: the complete 3\/8\" drive metric set, shallow and deep, 6-point, 6–24mm, 38 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one STL, size labels recessed into the surface\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer)\u003cbr\u003e\nBuilt to the Tekton SHD91211 set. Shallow sockets stand upright; deep sockets lie flat in labeled troughs. It nests top and bottom, so prints stack.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Tekton SHD91211 3\/8\" metric sockets. Other brands and sets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 41 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: we print ours as-is with supports turned off\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eCOLOUR\u003cbr\u003e\n- The file prints in one colour as-is. The size labels are recessed, so they read clearly in a single colour.\u003cbr\u003e\n- Want contrasting labels like ours? Colour the label faces with your slicer's paint tool. A warning that the labels are not on the top surface is expected: they sit inside recesses on purpose.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67614172053740,"sku":"TEK-011-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/tek-011-dig-01-metric-organizer-render.jpg?v=1792945566"},{"product_id":"milwaukee-packout-3-8-drive-socket-organizer-stl-file-tekton-skt15101-6-point-sae-shallow-deep-34-pc","title":"Milwaukee Packout 3\/8\" Drive Socket Organizer STL File for Tekton SKT15101 6-Point SAE, Shallow \u0026 Deep, 1\/4\"–1\" (34-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Tekton SKT15101 organizer insert: the complete 3\/8\" drive SAE set, shallow and deep 6-point sockets 1\/4\"–1\" plus the ratchet, both extensions and the universal joint, 34 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, tools, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one STL, size labels recessed into the surface\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer)\u003cbr\u003e\nBuilt to the Tekton SKT15101 set. Shallow sockets stand upright; deep sockets lie flat in labeled troughs; the ratchet, extensions and universal joint have their own pockets. It nests top and bottom, so prints stack.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Tekton SKT15101 3\/8\" SAE sockets and tools. Other brands and sets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 41 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: we print ours as-is with supports turned off\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eCOLOUR\u003cbr\u003e\n- The file prints in one colour as-is. The size labels are recessed, so they read clearly in a single colour.\u003cbr\u003e\n- Want contrasting labels like ours? Colour the label faces with your slicer's paint tool. A warning that the labels are not on the top surface is expected: they sit inside recesses on purpose.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67614172250348,"sku":"TEK-010-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/tek-010-dig-01-sae-organizer-render.jpg?v=1791131437"},{"product_id":"milwaukee-packout-1-2-milwaukee-shockwave-metric-deep-6-point-impact-socket-organizer-stl-file-no-skip-complete-series-49-66-7015-8mm-36mm","title":"Milwaukee Packout 1\/2\" Milwaukee Shockwave Metric Deep 6-Point Impact Socket Organizer STL File – No-Skip Complete Series, 49-66-7015 (8mm–36mm)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert: the complete 1\/2\" drive metric deep impact lineup, 6-point, 8–36mm, 29 sockets, no skipped sizes, every size labeled. It matches Milwaukee's 49-66-7015 set.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e (organizer base and support lid): the same two-piece design we print for the finished insert. The deep sockets stand in the base, and the lid snaps in on top to brace them part way up.\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split each piece with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Deep Organizer) and 48-22-8435 (Compact Deep Organizer)\u003cbr\u003e\n✔ Tool chest drawers with at least 86 mm of clear height (the sockets stand about 85 mm tall)\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 1\/2\" metric deep impact sockets, 8mm through 36mm. Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 1\/2\" metric deep impact sockets. Other brands and standard-depth sockets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Two pieces, each 293 × 193 mm: the base is 48.5 mm tall and the lid 11 mm. Your bed must be at least about 300 × 200 mm. They do \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print each piece as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels and logo are raised 1 mm on top of the lid. To print them in a second colour, add a filament change at the first layer above 10.0 mm on the lid and keep it to the end.\u003cbr\u003e\n- The base prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67628592070892,"sku":"MIL-005-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-005-dig-01-metric-organizer-render.jpg?v=1792942488"},{"product_id":"milwaukee-packout-1-2-milwaukee-shockwave-sae-deep-6-point-impact-socket-organizer-stl-file-no-skip-complete-series-3-8-1-9-16","title":"Milwaukee Packout 1\/2\" Milwaukee Shockwave SAE Deep 6-Point Impact Socket Organizer STL File – No-Skip Complete Series (3\/8\"–1-9\/16\")","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert: the complete 1\/2\" drive SAE deep impact lineup, 6-point, 3\/8\" through 1-9\/16\", 20 sockets, no skipped sizes, every size labeled. Milwaukee sells 19 of these sizes in its 49-66-7012 set; the 1-9\/16\" is sold individually, and it has its own pocket too.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e (organizer base and support lid): the same two-piece design we print for the finished insert. The deep sockets stand in the base, and the lid snaps in on top to brace them part way up.\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split each piece with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Deep Organizer) and 48-22-8435 (Compact Deep Organizer)\u003cbr\u003e\n✔ Tool chest drawers with at least 86 mm of clear height (the sockets stand about 85 mm tall)\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 1\/2\" SAE deep impact sockets, 3\/8\" through 1-9\/16\". Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 1\/2\" SAE deep impact sockets. Other brands and standard-depth sockets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Two pieces, each 293 × 193 mm: the base is 48.5 mm tall and the lid 11 mm. Your bed must be at least about 300 × 200 mm. They do \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print each piece as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels and logo are raised 1 mm on top of the lid. To print them in a second colour, add a filament change at the first layer above 10.0 mm on the lid and keep it to the end.\u003cbr\u003e\n- The base prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67657455304940,"sku":"MIL-003-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-003-dig-01-sae-organizer-render.jpg?v=1791291878"},{"product_id":"milwaukee-packout-1-2-drive-milwaukee-shockwave-sae-shallow-6-point-impact-socket-organizer-stl-file-no-skip-complete-series-3-8-1-9-16","title":"Milwaukee Packout 1\/2\" Drive Milwaukee Shockwave SAE Shallow 6-Point Impact Socket Organizer STL File – No-Skip Complete Series (3\/8\"–1-9\/16\")","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert: the complete 1\/2\" drive SAE standard-depth (shallow) impact lineup, 6-point, 3\/8\" through 1-9\/16\", 20 sockets, no skipped sizes, every size labeled. Milwaukee sells this range across several sets; the file holds all 20 sizes however you've built your collection.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece, the same design we print for the finished insert\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Standard tool chest drawers with at least 58 mm of clear height (the organizer stands 57.5 mm tall)\u003cbr\u003e\nWith an adapter: Milwaukee Packout deep organizers (48-22-8430 and 48-22-8435) and Packout drawers, using our spacer tray or drawer adapters (sold separately). Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 1\/2\" SAE standard-depth impact sockets, 3\/8\" through 1-9\/16\". The sockets stand upright in labeled pockets on four stepped decks.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 1\/2\" SAE standard-depth impact sockets. Other brands and deep sockets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 57.5 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels are raised 1 mm, on four decks at different heights, so a single filament change won't colour them on its own.\u003cbr\u003e\n- To print them in a second colour, paint the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise the organizer prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67658515513580,"sku":"MIL-012-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-012-dig-01-sae-organizer-render.jpg?v=1791291104"},{"product_id":"milwaukee-packout-3-8-milwaukee-shockwave-6-point-impact-socket-organizer-stl-file-sae-metric-49-66-7009-43-pc","title":"Milwaukee Packout 3\/8\" Milwaukee Shockwave 6-Point Impact Socket Organizer STL File – SAE \u0026 Metric, 49-66-7009 (43-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE 49-66-7009 organizer insert: the complete 3\/8\" drive SAE and metric impact set, standard and deep, 6-point, plus the set's accessories, 43 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne STL file\u003c\/strong\u003e: the whole organizer as one piece, with the sizes debossed into the surface\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT IT HOLDS\u003cbr\u003e\n- SAE standard and deep: 5\/16\", 3\/8\", 7\/16\", 1\/2\", 9\/16\", 5\/8\", 11\/16\", 3\/4\" (16 sockets)\u003cbr\u003e\n- Metric standard and deep: 8mm through 19mm (24 sockets)\u003cbr\u003e\n- The set's 3\" extension, universal joint and 3\/8\" adapter\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer), and standard tool chest drawers, no adapter\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Deep Organizer) and 48-22-8435 (Compact Deep Organizer), Packout slim, medium and deep drawers, and the Bauer 71125 drawer, each with the matching Mountaineer Maker spacer or adapter (sold separately)\u003cbr\u003e\nBuilt to the Milwaukee SHOCKWAVE 49-66-7009 set: every socket and accessory that comes in the box.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the Milwaukee SHOCKWAVE 49-66-7009 set. Sockets from other brands or sets may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 41 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003cbr\u003e\n- The size labels are debossed, so it prints in one colour with nothing to swap.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67658817208556,"sku":"MIL-006-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-006-dig-01-organizer-render.jpg?v=1791292546"},{"product_id":"milwaukee-packout-1-2-shockwave-metric-impact-socket-organizer-set-stl-file-deep-standard-10-27mm-36-pc","title":"Milwaukee Packout 1\/2\" Shockwave Metric Impact Socket Organizer Set STL File – Deep \u0026 Standard 10–27mm (36-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer set yourself.\u003c\/strong\u003e This is the 3D print file for our two-organizer Milwaukee SHOCKWAVE set: 1\/2\" drive metric impact sockets, 6-point, 10mm through 27mm in both deep and standard depth, 36 sockets, every socket labeled. A deep-socket base organizer sits at the bottom and a second organizer, holding the standard sockets and the large deep sizes, nests on top of it.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizers and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the base organizer and the top organizer, one file each, the same design we print for the finished set\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split each organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT GOES WHERE\u003cbr\u003e\n- \u003cstrong\u003eBase organizer\u003c\/strong\u003e (13 sockets): the deep sockets 10mm–22mm, lying flat in labeled troughs\u003cbr\u003e\n- \u003cstrong\u003eTop organizer\u003c\/strong\u003e (23 sockets): all 18 standard sockets 10mm–27mm standing upright, plus the large deep sockets 23mm–27mm lying flat\u003cbr\u003e\nMilwaukee doesn't sell this range as one set; the files hold it however you've built your collection. Sizes below 10mm and above 27mm are not included.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout organizers 48-22-8430 and 48-22-8435: the base drops in, the top nests on it, and the lid closes\u003cbr\u003e\n✔ Standard tool chest drawers with at least 75 mm of clear height for the stacked pair (each organizer is 37 mm tall)\u003cbr\u003e\nWith an adapter: Packout drawers and the Bauer 71125 drawer, using our drawer adapters (sold separately). Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 1\/2\" metric impact sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Two pieces, each 293 × 193 × 37 mm. Your bed must be at least about 300 × 200 mm. They do \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Print each one flat side down. The base organizer prints without supports; turn on your slicer's automatic supports for the top organizer (we use them for its first few millimetres)\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels are raised 1 mm, so you can print them in a second colour by painting the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise each organizer prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67659784093932,"sku":"MIL-007-DIG","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-007-dig-01-metric-organizer-set-render.jpg?v=1792954853"},{"product_id":"milwaukee-packout-3-8-swivel-impact-socket-organizer-stl-file-icon-59745-59747-6-point-sae-metric-22-pc","title":"Milwaukee Packout 3\/8\" Drive Swivel Impact Socket Organizer STL File for Harbor Freight Icon 59745\/59747 6-Point SAE \u0026 Metric (22-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Icon swivel impact socket organizer insert: both Harbor Freight Icon 3\/8\" drive swivel impact sets in one organizer, the 59745 SAE 12-piece (5\/16\" through 1\") and the 59747 metric 10-piece (10mm through 19mm), 22 sockets, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece, the same design we print for the finished insert\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED (Icon part numbers)\u003cbr\u003e\nSAE: 5\/16\" 12US31 · 3\/8\" 12US38 · 7\/16\" 12US44 · 1\/2\" 12US50 · 9\/16\" 12US56 · 5\/8\" 12US63 · 11\/16\" 12US69 · 3\/4\" 12US75 · 13\/16\" 12US81 · 7\/8\" 12US88 · 15\/16\" 12US94 · 1\" 12US100\u003cbr\u003e\nMetric: 10mm 12UM10 · 11mm 12UM11 · 12mm 12UM12 · 13mm 12UM13 · 14mm 12UM14 · 15mm 12UM15 · 16mm 12UM16 · 17mm 12UM17 · 18mm 12UM18 · 19mm 12UM19\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers 48-22-8431 and 48-22-8436, and standard tool chest drawers: drops straight in\u003cbr\u003e\nWith an adapter: Packout deep organizers (48-22-8430 and 48-22-8435) and Packout drawers, using our spacer trays or drawer adapters (sold separately).\u003cbr\u003e\nThe swivel sockets lie on their sides in labeled pockets shaped to the swivel head.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Icon's 3\/8\" swivel impact sockets. The swivel head is larger than a standard socket of the same size, so standard sockets or other brands' swivels may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 41 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels and logo are raised 1 mm above the deck. The organizer's walls rise above them, so a filament change at the label height would colour the wall tops too.\u003cbr\u003e\n- To print the labels in a second colour, paint the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise the organizer prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67660293275884,"sku":"ICN-001-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/icn-001-dig-01-organizer-render.jpg?v=1791298349"},{"product_id":"milwaukee-packout-1-2-shockwave-sae-impact-socket-organizer-set-stl-file-deep-standard-3-8-1-1-2-38-pc","title":"Milwaukee Packout 1\/2\" Shockwave SAE Impact Socket Organizer Set STL File – Deep \u0026 Standard 3\/8\"–1-1\/2\" (38-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer set yourself.\u003c\/strong\u003e This is the 3D print file for our two-organizer Milwaukee SHOCKWAVE set: 1\/2\" drive SAE impact sockets, 6-point, 3\/8\" through 1-1\/2\" in both deep and standard depth, 38 sockets, every socket labeled. A deep-socket base organizer sits at the bottom and a second organizer, holding the standard sockets and the large deep sizes, nests on top of it.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizers and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the base organizer and the top organizer, one file each, the same design we print for the finished set\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split each organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT GOES WHERE\u003cbr\u003e\n- \u003cstrong\u003eBase organizer\u003c\/strong\u003e (14 sockets): the deep sockets 3\/8\"–1-3\/16\", lying flat in labeled troughs\u003cbr\u003e\n- \u003cstrong\u003eTop organizer\u003c\/strong\u003e (24 sockets): all 19 standard sockets 3\/8\"–1-1\/2\" standing upright, plus the large deep sockets 1-1\/4\"–1-1\/2\" lying flat\u003cbr\u003e\nMilwaukee doesn't sell this range as one set; the files hold it however you've built your collection. The 1-9\/16\" size is not included in either depth.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout organizers 48-22-8430 and 48-22-8435: the base drops in, the top nests on it, and the lid closes\u003cbr\u003e\n✔ Standard tool chest drawers deep enough for the stacked pair (the base is 45 mm tall, the top 33 mm)\u003cbr\u003e\nWith an adapter: Packout drawers and the Bauer 71125 drawer, using our drawer adapters (sold separately). Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Milwaukee SHOCKWAVE 1\/2\" SAE impact sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Two pieces, each 293 × 193 mm: the base is 45 mm tall and the top 33 mm. Your bed must be at least about 300 × 200 mm. They do \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Print each one as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels are raised, so you can print them in a second colour by painting the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise each organizer prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67660354093292,"sku":"MIL-008-DIG","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-008-dig-01-sae-organizer-set-render.jpg?v=1791295796"},{"product_id":"milwaukee-packout-3-8-drive-impact-socket-organizer-stl-file-icon-70432-59756-6-point-metric-deep-shallow-26-pc","title":"Milwaukee Packout 3\/8\" Drive Impact Socket Organizer STL File for Harbor Freight Icon 70432\/59756 6-Point Metric Deep \u0026 Shallow (26-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Icon metric impact socket organizer insert: both Harbor Freight Icon 3\/8\" drive metric impact sets in one organizer, the 70432 standard 13-piece and the 59756 deep 13-piece (7mm through 19mm), 26 sockets, every size labeled, plus a built-in storage compartment.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece, the same design we print for the finished insert\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED (Icon part numbers, standard \/ deep)\u003cbr\u003e\n7mm 12SM7 \/ 12DM7 · 8mm 12SM8 \/ 12DM8 · 9mm 12SM9 \/ 12DM9 · 10mm 12SM10 \/ 12DM10 · 11mm 12SM11 \/ 12DM11 · 12mm 12SM12 \/ 12DM12 · 13mm 12SM13 \/ 12DM13 · 14mm 12SM14 \/ 12DM14 · 15mm 12SM15 \/ 12DM15 · 16mm 12SM16 \/ 12DM16 · 17mm 12SM17 \/ 12DM17 · 18mm 12SM18 \/ 12DM18 · 19mm 12SM19 \/ 12DM19\u003c\/p\u003e\n\n\u003cp\u003eQUICK SCAN\u003cbr\u003e\n- Both Icon 3\/8\" metric impact sets, standard and deep, in one organizer\u003cbr\u003e\n- Built-in storage compartment (about 11.25\" × 2.5\" × 1.25\") for a ratchet, extensions or anything else you keep with the set\u003cbr\u003e\n- Pair it with our Icon SAE organizer to carry the whole Icon 3\/8\" impact lineup\u003cbr\u003e\n- Print it yourself, in any colors you want\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers 48-22-8431 and 48-22-8436, and standard tool chest drawers: drops straight in\u003cbr\u003e\nWith an adapter: Packout deep organizers (48-22-8430 and 48-22-8435) and Packout drawers, using our spacer trays or drawer adapters (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Icon's 3\/8\" metric standard and deep impact sockets. Sockets from another brand, or a different drive or system, may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 34 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels are raised 1 mm above their decks, and the decks sit at several heights, so a single filament change can't colour them.\u003cbr\u003e\n- To print the labels in a second colour, paint the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise the organizer prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67669946073324,"sku":"ICN-003-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/icn-003-dig-01-organizer-render.jpg?v=1792945918"},{"product_id":"milwaukee-packout-3-8-drive-impact-socket-organizer-stl-file-icon-59750-59739-6-point-sae-deep-shallow-24-pc","title":"Milwaukee Packout 3\/8\" Drive Impact Socket Organizer STL File for Harbor Freight Icon 59750\/59739 6-Point SAE Deep \u0026 Shallow (24-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Icon SAE impact socket organizer insert: both Harbor Freight Icon 3\/8\" drive SAE impact sets in one organizer, the 59750 standard 12-piece and the 59739 deep 12-piece (5\/16\" through 1\"), 24 sockets, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece, the same design we print for the finished insert\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED (Icon part numbers, standard \/ deep)\u003cbr\u003e\n5\/16\" 12SS31 \/ 12DS31 · 3\/8\" 12SS38 \/ 12DS38 · 7\/16\" 12SS44 \/ 12DS44 · 1\/2\" 12SS50 \/ 12DS50 · 9\/16\" 12SS56 \/ 12DS56 · 5\/8\" 12SS63 \/ 12DS63 · 11\/16\" 12SS69 \/ 12DS69 · 3\/4\" 12SS75 \/ 12DS75 · 13\/16\" 12SS81 \/ 12DS81 · 7\/8\" 12SS88 \/ 12DS88 · 15\/16\" 12SS94 \/ 12DS94 · 1\" 12SS100 \/ 12DS100\u003c\/p\u003e\n\n\u003cp\u003eQUICK SCAN\u003cbr\u003e\n- Both Icon 3\/8\" SAE impact sets, standard and deep, in one organizer\u003cbr\u003e\n- Standard sockets stand upright; deep sockets lie flat in labeled troughs\u003cbr\u003e\n- The 5\/16\" deep pocket holds its socket with a little retention, so it takes slightly more effort to lift out than the other sizes, by design\u003cbr\u003e\n- Pair it with our Icon metric organizer to carry the whole Icon 3\/8\" impact lineup\u003cbr\u003e\n- Print it yourself, in any colors you want\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers 48-22-8431 and 48-22-8436, and standard tool chest drawers: drops straight in\u003cbr\u003e\nWith an adapter: Packout deep organizers (48-22-8430 and 48-22-8435) and Packout drawers, using our spacer trays or drawer adapters (sold separately).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Icon's 3\/8\" SAE standard and deep impact sockets. Sockets from another brand, or a different drive or system, may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 37 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels are raised above their decks, and the decks sit at several heights, so a single filament change can't colour them.\u003cbr\u003e\n- To print the labels in a second colour, paint the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise the organizer prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67670265495788,"sku":"ICN-004-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/icn-004-dig-01-organizer-render.jpg?v=1791375039"},{"product_id":"milwaukee-packout-1-4-modular-impact-socket-organizer-stl-file-sunex-1848-6-point-sae-metric-48-pc","title":"Milwaukee Packout 1\/4\" Modular Impact Socket Organizer STL File – Sunex 1848 6-Point SAE \u0026 Metric (48-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our modular Milwaukee Packout organizer for the Sunex 1848 1\/4\" drive impact master set: 6-point SAE and metric, standard and deep, 48 sockets, every socket labeled. An outer frame holds a metric tray, an SAE tray and a storage tray with a removable rack, so you can lift just the tray you need out to the bench.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eFive STL files\u003c\/strong\u003e, one per printed part: the outer frame, the metric tray, the SAE tray, the storage tray and its removable rack. The same design we print for the finished organizer\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the frame with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT GOES WHERE\u003cbr\u003e\n- \u003cstrong\u003eSAE tray\u003c\/strong\u003e (20 sockets): 3\/16\"–9\/16\", standard sockets upright and deep sockets lying flat in labeled troughs\u003cbr\u003e\n- \u003cstrong\u003eMetric tray\u003c\/strong\u003e (28 sockets): 4mm–15mm including 4.5 and 5.5mm, standard upright and deep lying flat\u003cbr\u003e\n- \u003cstrong\u003eStorage tray and rack\u003c\/strong\u003e: open space for the ratchet, extensions and adapters you carry with the set (not included)\u003cbr\u003e\nSunex sells this range as the 1848 master set: 48 pieces, no gaps. The 11\/32\" deep socket is held by a retention fit; every other socket lifts straight out.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers 48-22-8431 and 48-22-8436\u003cbr\u003e\n✔ Standard tool chest drawers (the frame is 293 × 193 × 41 mm)\u003cbr\u003e\nWith an adapter or spacer (sold separately): the deep Packout organizers 48-22-8430 and 48-22-8435, and Packout drawers. The frame nests with our other organizers, above and below.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the CHINA-made Sunex 1848 set. Sunex also makes the 1848 in Taiwan with different socket dimensions, and those sockets, or another brand's, may not fit. China-made Sunex sockets do not carry a \"TAIWAN\" stamp; if yours are stamped Taiwan, message us before buying.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Five pieces. The largest is the frame, 293 × 193 mm and 41 mm tall; the trays are 182 mm wide. Your bed must be at least about 300 × 200 mm for the frame. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Print each part as it loads, flat side down. No supports needed\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels and logos on the two socket trays are raised 1 mm, so you can print them in a second colour by painting the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise each part prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67670279848172,"sku":"SUN-001-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/sun-001-dig-01-organizer-render.jpg?v=1791379356"},{"product_id":"milwaukee-packout-1-2-drive-deep-shallow-socket-organizer-stl-file-milwaukee-shockwave-6-point-metric-impact-9-24mm-32-pc","title":"Milwaukee Packout 1\/2\" Drive Deep \u0026 Shallow Socket Organizer STL File for Milwaukee Shockwave 6-Point Metric Impact, 9–24mm (32-Pc) + 3\" Extension","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert: 1\/2\" drive metric impact sockets from 9mm to 24mm, deep and shallow, 6-point, 32 sockets plus a 3\" extension, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, extension, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eFour STL files\u003c\/strong\u003e: the organizer base and the lift-out shallow insert, plus a separate labels file for each, so the size labels and logo can print in a second colour. The deep sockets stand upright in the base. The shallow sockets ride on the lift-out insert, which drops into a 45-degree taper seat and centres itself; under it is open storage with a snap-in cradle in the base for a 3\" extension. Four of the larger shallow pockets have 20 mm lift holes, ringed in the label colour, so you can push those sockets up from below.\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8435 (Compact Deep Organizer) and 48-22-8430 (Deep Organizer)\u003cbr\u003e\n✔ Tool chest drawers with at least 86 mm of clear height (the deep sockets stand about 85 mm tall)\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 1\/2\" metric impact sockets, 9mm through 24mm, deep and shallow. Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to measured Milwaukee SHOCKWAVE 1\/2\" metric impact sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Two pieces: the base is 293 × 193 × 47 mm and the shallow insert 150.5 × 193 × 23 mm. Your bed must be at least about 300 × 200 mm for the base. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print both pieces upright, pockets up, as they load\u003cbr\u003e\n- Designed on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- Load each piece together with its labels file as one multi-part object and assign the labels a second filament. The labels sit in place on top of the piece.\u003cbr\u003e\n- For one colour, print the base and insert files alone.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67671535976684,"sku":"MIL-013-DIG","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-013-dig-01-metric-organizer-render-v11.jpg?v=1792944619"},{"product_id":"milwaukee-packout-3-8-impact-socket-organizer-stl-file-sunex-3342-6-point-sae-metric-standard-deep-42-pc","title":"Milwaukee Packout 3\/8\" Impact Socket Organizer STL File – Sunex 3342 6-Point SAE \u0026 Metric, Standard \u0026 Deep (42-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout organizer insert for the Sunex 3342 3\/8\" drive impact master set: 6-point SAE and metric, standard and deep, plus the set's 3\" extension and universal joint, 42 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne STL file\u003c\/strong\u003e: the whole organizer as one piece, with the sizes debossed into the surface\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT IT HOLDS\u003cbr\u003e\n- SAE standard and deep: 5\/16\", 3\/8\", 7\/16\", 1\/2\", 9\/16\", 5\/8\", 11\/16\", 3\/4\" (16 sockets)\u003cbr\u003e\n- Metric standard and deep: 8mm through 19mm (24 sockets)\u003cbr\u003e\n- The set's 3\" extension and universal joint\u003cbr\u003e\nStandard sockets stand upright in two center rows; deep sockets lie flat in labeled troughs along both long sides.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer), and standard tool chest drawers, no adapter\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Deep Organizer) and 48-22-8435 (Compact Deep Organizer), and Packout slim, medium and deep drawers, each with the matching Mountaineer Maker spacer or adapter (sold separately)\u003cbr\u003e\nIt nests with our other organizers, above and below. Built to the Sunex 3342 set: every socket and accessory that comes in the box.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the TAIWAN-made Sunex 3342 set. Sunex has since moved production of this set to China, and the socket dimensions changed; China-made sockets, or another brand's, may not fit. Taiwan-made Sunex sockets are stamped \"TAIWAN\" on the body. If yours aren't, message us before buying.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 41 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003cbr\u003e\n- The size labels are debossed, so it prints in one colour with nothing to swap.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67675211825388,"sku":"SUN-002-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/sun-002-dig-01-organizer-render.jpg?v=1791458192"},{"product_id":"milwaukee-packout-1-2-drive-swivel-impact-socket-organizer-stl-file-for-harbor-freight-icon-59741-6-point-sae-14-pc","title":"Milwaukee Packout 1\/2\" Drive Swivel Impact Socket Organizer STL\/3MF File for Harbor Freight Icon 59741 6-Point SAE (14-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Icon swivel impact socket organizer insert: the complete Harbor Freight Icon 59741 1\/2\" drive SAE impact swivel set, 14 sockets from 7\/16\" to 1-1\/4\", 6-point, each lying flat in its own labeled pocket. It now includes the matching retention lid, which keeps the swivels in their seats under a Packout lid.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo 3MF files\u003c\/strong\u003e, organizer and retention lid, each with the base and labels already set up as one two-colour object\u003cbr\u003e\n- \u003cstrong\u003eFour STL files\u003c\/strong\u003e: the organizer base and its labels, and the retention lid and its labels, each labels file already in place for a second colour\u003cbr\u003e\n- \u003cstrong\u003eThe retention lid\u003c\/strong\u003e: a thin slab that drops into the top of the organizer and sits just above the sockets, so a swivel can't lift out of its seat under a Packout lid. No latch, a finger hole to lift it off, and a size map on top: every pocket outlined with its size inside\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED (Icon 59741)\u003cbr\u003e\n7\/16\" · 1\/2\" · 9\/16\" · 5\/8\" · 11\/16\" · 3\/4\" · 13\/16\" · 7\/8\" · 15\/16\" · 1\" · 1-1\/16\" · 1-1\/8\" · 1-3\/16\" · 1-1\/4\"\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Standard tool chest drawers: drops straight in\u003cbr\u003e\nWith a 37 mm spacer: Milwaukee Packout deep organizers 48-22-8430 and 48-22-8435\u003cbr\u003e\n✘ Not the Packout low-profile organizers 48-22-8431 and 48-22-8436: the larger sockets in this set are too big for them.\u003cbr\u003e\nEach swivel lies on its side in a cradle shaped to its drive end, shoulder and swivel end. Sizes are labeled on the deck and in every pocket, so you can read them with the socket in or out. The retention lid sits flush with the organizer's rim, so it adds no height.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Icon's 1\/2\" SAE swivel impact sockets, from caliper measurements of the actual set. The swivel head is larger than a standard socket of the same size, so standard sockets, Icon's metric swivels or other brands' swivels may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Organizer: one piece, 293 × 193 × 54 mm. Retention lid: one piece, 293 × 193 × 4 mm. Your bed must be at least about 300 × 200 mm. Neither fits 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut the organizer to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print each part as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS\u003cbr\u003e\n- \u003cstrong\u003eEasiest:\u003c\/strong\u003e open the 3MF. Base and labels are already one object on two filaments; pick your two colours.\u003cbr\u003e\n- With the STLs: import a base and its labels file together and load them as \u003cstrong\u003eone object with multiple parts\u003c\/strong\u003e, without re-arranging, so every label stays in its place. Give the labels part your second filament.\u003cbr\u003e\n- One colour only? Leave both parts on the same filament.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67676581429484,"sku":"ICN-007-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/icn-007-dig-01-sae-organizer-render.jpg?v=1791472938"},{"product_id":"milwaukee-packout-1-4-tekton-skt05303-modular-socket-organizer-stl-file-sae-metric-chrome-56-pc","title":"Milwaukee Packout 1\/4\" Tekton SKT05303 Modular Socket Organizer STL File – SAE \u0026 Metric Chrome (56-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our modular Milwaukee Packout organizer for the Tekton SKT05303 1\/4\" drive set: 6-point SAE and metric, standard and deep, 50 sockets plus the six drive tools, every socket labeled. An outer frame holds four removable trays (SAE, metric, ratchet and accessories, spinner handle), so you can lift just the tray you need out to the bench. A one-piece version is included too.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, tools, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eFive STL files for the modular organizer\u003c\/strong\u003e, one per printed part: the outer frame, the SAE tray, the metric tray, the ratchet tray and the spinner-handle tray. The same design we print for the finished organizer\u003cbr\u003e\n- \u003cstrong\u003eOne STL file for the one-piece organizer\u003c\/strong\u003e: the same layout as a single part, if you'd rather print it in one go\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the frame or the one-piece with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT GOES WHERE\u003cbr\u003e\n- \u003cstrong\u003eSAE tray\u003c\/strong\u003e (22 sockets): 5\/32\"–9\/16\", standard sockets upright and deep sockets lying flat in labeled troughs\u003cbr\u003e\n- \u003cstrong\u003eMetric tray\u003c\/strong\u003e (28 sockets): 4mm–15mm including 4.5 and 5.5mm, standard upright and deep lying flat\u003cbr\u003e\n- \u003cstrong\u003eRatchet tray\u003c\/strong\u003e: the quick-release ratchet, the 3\" and 6\" extensions, the universal joint and the magnetic bit holder\u003cbr\u003e\n- \u003cstrong\u003eSpinner-handle tray\u003c\/strong\u003e: the 6.5\" spinner handle\u003cbr\u003e\nTekton sells this range as the SKT05303 56-piece set.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers 48-22-8431 and 48-22-8436\u003cbr\u003e\n✔ Standard tool chest drawers (the organizer is 293 × 193 × 41 mm)\u003cbr\u003e\nWith an adapter or spacer (sold separately): the deep Packout organizers 48-22-8430 and 48-22-8435, and Packout drawers. The frame nests with our other organizers, above and below.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the exact dimensions of Tekton SKT05303 1\/4\" chrome sockets. Sockets from a different brand or a different point count may not fit.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The largest part is the frame (or the one-piece), 293 × 193 mm and 41 mm tall; the trays are 182 mm wide. Your bed must be at least about 300 × 200 mm for the frame. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Print each part as it loads, flat side down. No supports needed\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels, headings and logo are raised, so you can print them in a second colour by painting the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise each part prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67677743022316,"sku":"TEK-002-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/tek-002-dig-01-organizer-render.jpg?v=1791499503"},{"product_id":"milwaukee-packout-1-4-modular-socket-organizer-stl-file-gearwrench-80300p-6-point-sae-metric-51-pc","title":"Milwaukee Packout 1\/4\" Modular Socket Organizer STL File – GearWrench 80300P 6-Point SAE \u0026 Metric (51-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our modular Milwaukee Packout organizer for the GearWrench 80300P 1\/4\" drive set: 6-point SAE and metric, standard and deep, 46 sockets plus the five drive tools, every socket labeled. An outer frame holds three removable parts (an SAE tray, a metric tray and a tool rack), so you can lift just the one you need out to the bench. A one-piece version is included too.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, tools, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eFour STL files for the modular organizer\u003c\/strong\u003e, one per printed part: the outer frame, the SAE tray, the metric tray and the tool rack. The same design we print for the finished organizer\u003cbr\u003e\n- \u003cstrong\u003eOne STL file for the one-piece organizer\u003c\/strong\u003e: the same socket layout as a single part, with an open bay that takes the same tool rack\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the frame or the one-piece with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT GOES WHERE\u003cbr\u003e\n- \u003cstrong\u003eSAE tray\u003c\/strong\u003e (20 sockets): 3\/16\"–9\/16\", standard sockets upright and deep sockets lying flat in labeled troughs\u003cbr\u003e\n- \u003cstrong\u003eMetric tray\u003c\/strong\u003e (26 sockets): 4mm–15mm including 5.5mm, standard sockets upright and deep sockets lying flat\u003cbr\u003e\n- \u003cstrong\u003eTool rack\u003c\/strong\u003e: the 120XP ratchet, the thumbwheel ratchet, the 2\" and 6\" extensions and the universal joint\u003cbr\u003e\nGearWrench sells this range as the 80300P 51-piece set.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers 48-22-8431 and 48-22-8436\u003cbr\u003e\n✔ Standard tool chest drawers (the organizer is 293 × 193 × 41 mm)\u003cbr\u003e\nWith an adapter or spacer (sold separately): the deep Packout organizers 48-22-8430 and 48-22-8435, and Packout drawers. The frame nests with our other organizers, above and below.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the exact dimensions of GearWrench 80300P 1\/4\" 6-point sockets and tools. Sockets from a different brand or a different set may not fit.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The largest part is the frame (or the one-piece), 293 × 193 mm and 41 mm tall; the trays and the tool rack are 182 mm wide or less. Your bed must be at least about 300 × 200 mm for the frame. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Print each part as it loads, flat side down. No supports needed\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels, headings and logo are raised, so you can print them in a second colour by painting the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise each part prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67694825439468,"sku":"GRW-002-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/grw-002-dig-01-organizer-render.jpg?v=1791564163"},{"product_id":"bauer-modular-drawer-71125-1-2-drive-deep-impact-socket-organizer-stl-file-icon-59748-59746-sae-metric","title":"Bauer Modular Drawer 71125 1\/2\" Drive Deep Impact Socket Organizer STL File for Harbor Freight Icon 59748\/59746 6-Point SAE \u0026 Metric (27-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Icon 1\/2\" deep impact socket organizer for the Bauer 71125 modular drawer: both Harbor Freight Icon 1\/2\" drive deep impact sets in one drawer, 27 sockets, SAE and metric, every socket lying flat in its own labeled pocket.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the organizer as a left half (SAE) and a right half (metric), the same design we print for the finished insert\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the raised labels for each half (size labels, SAE and METRIC headings, MM logo), for a second colour\u003cbr\u003e\n- \u003cstrong\u003eThree STL files\u003c\/strong\u003e: the risers that lift the organizer level above the drawer's floor ribs\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer)\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSETS COVERED (Icon item numbers)\u003cbr\u003e\n- SAE deep, 13 sockets 7\/16\"–1-1\/4\": 59748\u003cbr\u003e\n- Metric deep, 14 sockets 10–27 mm: 59746\u003c\/p\u003e\n\n\u003cp\u003eQUICK SCAN\u003cbr\u003e\n- Both Icon 1\/2\" deep impact sets in one Bauer 71125 drawer\u003cbr\u003e\n- SAE on the left, metric on the right, every column in size order\u003cbr\u003e\n- Three open bins at the back for extensions and adapters\u003cbr\u003e\n- Print it yourself, in any colors you want\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Bauer modular drawer 71125, both the original drawer and the current one with divider posts on the floor ribs: the two halves sit side by side on the included risers and drop straight in\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Icon's 1\/2\" deep impact sockets. Sockets from another brand, or a different drive, may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The organizer comes in two halves, about 200 × 279 × 24.5 mm each (398 × 279 × 39.5 mm assembled on the risers). The risers are 122 × 279 × 15 mm (two) and 118 × 279 × 15 mm (one).\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print each part as it loads, flat side down\u003cbr\u003e\n- Designed on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- Each half has a matching labels STL. Load it into your slicer as a part of that half (same position, it sits on top) and give it your second filament.\u003cbr\u003e\n- Skip the labels STL and the organizer prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67695989620972,"sku":"ICN-006-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/icn-006-dig-01-organizer-render.jpg?v=1791575748"},{"product_id":"packout-storage-spacer-tray-stl-file","title":"Milwaukee Packout Deep Organizer Spacer \u0026 Storage Tray – 33.5mm for Compatible Socket Organizers (48-22-8430 \/ 48-22-8435) – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the spacer tray yourself.\u003c\/strong\u003e This is the 3D print file for our 33.5 mm spacer and storage tray. It lifts a compatible Mountaineer Maker socket organizer to the right height in a deep Milwaukee Packout organizer, so the lid holds the sockets in place, and gives you a closed storage compartment underneath.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizers, sockets and the Packout box are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole spacer tray as one piece\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Organizer) and 48-22-8435 (Compact Organizer)\u003cbr\u003e\nIt nests with our organizers, under or on top of the organizer. The storage area inside is 283 × 183 mm and 28 mm deep. Check your organizer's compatibility chart to confirm 33.5 mm is the spacer height it needs.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 38.5 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: the tray has no overhangs\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished spacer in our shop. Not sure which spacer height you need? Message us and we'll help you choose.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696050143468,"sku":"MIL-SPACER-335-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-spacer-335-dig-01-hero.jpg?v=1791576477"},{"product_id":"milwaukee-packout-drawer-adapter-for-socket-organizer-inserts-fits-48-22-8444-and-48-22-8447-shallow-drawers-2-piece-set-stl-file","title":"Milwaukee Packout Drawer Adapter for Socket Organizer Inserts, Fits 48-22-8444 and 48-22-8447 Shallow Drawers, 2-Piece Set – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the drawer adapter yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout shallow-drawer adapter: a two-piece frame that turns a shallow Packout drawer into a bay for two of our nesting organizer inserts, side by side.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizer inserts, sockets and the Packout drawer unit are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: one half of the adapter. Print it twice; the second half sits end for end against the first\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ The shallow drawers of the Milwaukee Packout 48-22-8444 and 48-22-8447 drawer units\u003cbr\u003e\nThe shallow drawer floor is broken up by ribs, so an organizer has nothing to lock into. The adapter spans the ribs and gives the drawer the same nesting connection our organizers use to stack on each other.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: built for the Milwaukee Packout shallow drawer only. It is not designed for other drawer systems, the medium or deep Packout drawers, or the Packout organizer boxes.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Each half is 318 × 207 × 22.5 mm. Your bed must be at least about 320 × 210 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints flat on the bed with no supports\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished adapter in our shop. Don't have an organizer for your set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696050471148,"sku":"MIL-ADPT-SLIM-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-adpt-slim-dig-01-hero-v2.jpg?v=1792946917"},{"product_id":"milwaukee-packout-drawer-adapter-for-socket-organizer-inserts-fits-48-22-8443-48-22-8442-and-48-22-8447-medium-and-deep-drawers-2-piece-set-stl-file","title":"Milwaukee Packout Drawer Adapter for Socket Organizer Inserts, Fits 48-22-8443, 48-22-8442 and 48-22-8447 Medium and Deep Drawers, 2-Piece Set – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the drawer adapter yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout medium and deep drawer adapter: a two-piece frame, one piece per side, that turns a medium or deep Packout drawer into a bay for two of our nesting organizer inserts, side by side at the base. The organizer drops right in and centers itself.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizer inserts, sockets and the Packout drawer unit are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne STL file\u003c\/strong\u003e: the adapter half. Print it twice; the second piece is the same part turned around for the other side of the drawer\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ The medium and deep drawers of the Milwaukee Packout 48-22-8443, 48-22-8442 and 48-22-8447 drawer units\u003cbr\u003e\nThe medium and deep drawer floors are broken up by ribs, so an organizer has nothing to lock into. Each piece spans the ribs on its side and gives the drawer the same nesting connection our organizers use to stack on each other.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: built for the Milwaukee Packout medium and deep drawers only. It is not designed for other drawer systems, the shallow Packout drawer, or the Packout organizer boxes.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Each piece is 308 × 207 × 28 mm. Your bed must be at least about 310 × 210 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints flat on the bed with no supports\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished adapter in our shop. Don't have an organizer for your set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696050864364,"sku":"MIL-ADPT-MD-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-adpt-md-dig-01-hero-v2.jpg?v=1792947387"},{"product_id":"bauer-modular-drawer-71125-adapter-for-socket-organizer-inserts-harbor-freight-bauer-2-drawer-3-piece-set-stl-file","title":"Bauer Modular Drawer 71125 Adapter for Socket Organizer Inserts – Harbor Freight Bauer 2-Drawer, 3-Piece Set – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the drawer adapter yourself.\u003c\/strong\u003e This is the 3D print file for our Harbor Freight Bauer 71125 drawer adapter: three pieces that hold one of our standard socket organizer inserts centered in a Bauer 71125 drawer, with corner brackets that keep it from sliding. It fits both the original and the updated Bauer 71125 drawer base.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizer inserts, sockets and the Bauer toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the end piece and the center piece. Print the end piece twice (the second one turns around in the drawer) and the center piece once\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ The drawers of the Harbor Freight Bauer 71125 2-drawer toolbox, one adapter set per drawer, with either the original or the updated drawer base\u003cbr\u003e\nThe Bauer drawer floor is broken up by raised ribs. The three pieces sit between the ribs and lift the organizer just clear of them, and corner brackets on the two end pieces hold one organizer insert at all four corners. The end pieces are marked V2.0.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: built for the Harbor Freight Bauer 71125 drawer only. It is not designed for other Bauer toolboxes, such as the 58511, or for other drawer systems.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The largest piece is 279 × 122 × 25 mm. Your bed must be at least about 280 × 125 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints flat on the bed with no supports\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished adapter in our shop. Don't have an organizer for your set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696590323948,"sku":"BAU-ADPT-71125-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/bau-adpt-71125-dig-01-hero.jpg?v=1792954853"},{"product_id":"milwaukee-packout-1-2-drive-shallow-impact-socket-organizer-stl-file-sunex-2640-china-made-6-point-sae-19-pc","title":"Milwaukee Packout 1\/2\" Drive Shallow Impact Socket Organizer STL File for Sunex 2640 China-Made 6-Point SAE, 3\/8\"–1-1\/2\" (19-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout organizer insert for the China-made Sunex 2640 1\/2\" drive shallow impact set: 6-point SAE, 3\/8\" to 1-1\/2\", 19 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer, drawer adapter and Packout drawer are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne STL file\u003c\/strong\u003e: the whole organizer as one piece, with the size labels and logo raised 0.5 mm on the deck\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT IT HOLDS\u003cbr\u003e\n- SAE 6-point shallow impact sockets: 3\/8\", 7\/16\", 1\/2\", 9\/16\", 5\/8\", 11\/16\", 3\/4\", 13\/16\", 7\/8\", 15\/16\", 1\", 1-1\/16\", 1-1\/8\", 1-3\/16\", 1-1\/4\", 1-5\/16\", 1-3\/8\", 1-7\/16\", 1-1\/2\" (19 sockets)\u003cbr\u003e\nEvery socket stands upright in its own labeled pocket.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Organizer) and 48-22-8435 (Compact Organizer), with the Mountaineer Maker 37 mm spacer tray under it (sold separately)\u003cbr\u003e\n✔ Milwaukee Packout slim drawer, with the Mountaineer Maker drawer adapter (sold separately)\u003cbr\u003e\n✘ Too tall for the low-profile 48-22-8431 and 48-22-8436\u003cbr\u003e\nIt has our standard nesting foot and top, so it stacks and nests with our other organizers.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the CHINA-made Sunex 2640 set. Taiwan-made Sunex sockets, another depth or another brand may not fit. China-made Sunex sockets do not carry a \"TAIWAN\" stamp; if yours are stamped TAIWAN, message us before buying.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 54 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003cbr\u003e\n- Two colours, optional: the size labels and logo are raised 0.5 mm, so you can paint them a second colour with your slicer's paint tool, or print it all in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the \u003ca href=\"\/products\/milwaukee-packout-1-2-drive-shallow-impact-socket-organizer-insert-for-sunex-6-point-sae-19-pc\"\u003efinished organizer\u003c\/a\u003e in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696706322668,"sku":"SUN-003-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/sun-003-dig-01-organizer-render.jpg?v=1791585604"},{"product_id":"milwaukee-packout-1-2-drive-deep-impact-socket-organizer-stl-file-sunex-2641-china-made-6-point-sae-19-pc","title":"Milwaukee Packout 1\/2\" Drive Deep Impact Socket Organizer STL File for Sunex 2641 China-Made 6-Point SAE, 3\/8\"–1-1\/2\" (19-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout organizer insert for the China-made Sunex 2641 1\/2\" drive deep impact set: 6-point SAE, 3\/8\" to 1-1\/2\", 19 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer, drawer adapter and Packout drawer are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eThree STL files\u003c\/strong\u003e: the base, the support lid, and the lid's raised size labels and logo as their own part, so they can print in a second colour\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT IT HOLDS\u003cbr\u003e\n- SAE 6-point deep impact sockets: 3\/8\", 7\/16\", 1\/2\", 9\/16\", 5\/8\", 11\/16\", 3\/4\", 13\/16\", 7\/8\", 15\/16\", 1\", 1-1\/16\", 1-1\/8\", 1-3\/16\", 1-1\/4\", 1-5\/16\", 1-3\/8\", 1-7\/16\", 1-1\/2\" (19 sockets)\u003cbr\u003e\nEach socket stands upright in the base and passes through its own labeled hole in the support lid.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Organizer) and 48-22-8435 (Compact Organizer), no adapter\u003cbr\u003e\n✔ Milwaukee Packout deep drawer, with the Mountaineer Maker drawer adapter (sold separately)\u003cbr\u003e\nIt has our standard nesting foot, so it sits on our other organizers.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the CHINA-made Sunex 2641 set. Taiwan-made Sunex sockets, another depth or another brand may not fit. China-made Sunex sockets do not carry a \"TAIWAN\" stamp; if yours are stamped TAIWAN, message us before buying.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Two pieces: the base is 293 × 193 × 48.5 mm and the support lid 293 × 193 × 10.5 mm (49 mm tall together). Your bed must be at least about 300 × 200 mm. Neither piece fits a 256 × 256 mm bed whole.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print each piece as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003cbr\u003e\n- Two colours, optional: load the labels STL as a part of the lid and give it your second colour. For a one-colour lid, leave it out. The lid snaps into the base.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the \u003ca href=\"\/products\/milwaukee-packout-1-2-drive-deep-impact-socket-organizer-insert-for-sunex-6-point-sae-19-pc\"\u003efinished organizer\u003c\/a\u003e in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696706355436,"sku":"SUN-004-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/sun-004-dig-01-organizer-render.jpg?v=1791585630"},{"product_id":"milwaukee-packout-1-2-drive-shallow-impact-socket-organizer-stl-file-sunex-china-made-6-point-metric-22-pc","title":"Milwaukee Packout 1\/2\" Drive Shallow Impact Socket Organizer STL File for Sunex China-Made 6-Point Metric, 9–30mm (22-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout organizer insert for China-made Sunex 1\/2\" drive shallow impact sockets: 6-point metric, 9mm to 30mm, 22 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer, drawer adapter and Packout drawer are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne STL file\u003c\/strong\u003e: the whole organizer as one piece, with the size labels and logo raised 0.5 mm on the deck\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT IT HOLDS\u003cbr\u003e\n- Metric 6-point shallow impact sockets: 9mm through 30mm, every size (22 sockets)\u003cbr\u003e\nEvery socket stands upright in its own labeled pocket.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Organizer) and 48-22-8435 (Compact Organizer), with the Mountaineer Maker 37 mm spacer tray under it (sold separately)\u003cbr\u003e\n✔ Milwaukee Packout slim drawer, with the Mountaineer Maker drawer adapter (sold separately)\u003cbr\u003e\n✘ Too tall for the low-profile 48-22-8431 and 48-22-8436\u003cbr\u003e\nIt has our standard nesting foot and top, so it stacks and nests with our other organizers.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to CHINA-made Sunex 6-point metric shallow impact sockets. Taiwan-made Sunex sockets, another depth or another brand may not fit. China-made Sunex sockets do not carry a \"TAIWAN\" stamp; if yours are stamped TAIWAN, message us before buying.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 54 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003cbr\u003e\n- Two colours, optional: the size labels and logo are raised 0.5 mm, so you can paint them a second colour with your slicer's paint tool, or print it all in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the \u003ca href=\"\/products\/milwaukee-packout-1-2-drive-shallow-impact-socket-organizer-insert-for-sunex-6-point-metric-22-pc\"\u003efinished organizer\u003c\/a\u003e in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696706715884,"sku":"SUN-005-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/sun-005-dig-01-organizer-render.jpg?v=1792954854"},{"product_id":"milwaukee-packout-1-2-drive-deep-impact-socket-organizer-stl-file-sunex-china-made-6-point-metric-22-pc","title":"Milwaukee Packout 1\/2\" Drive Deep Impact Socket Organizer STL File for Sunex China-Made 6-Point Metric, 9–30mm (22-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout organizer insert for China-made Sunex 1\/2\" drive deep impact sockets: 6-point metric, 9mm to 30mm, 22 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer, drawer adapter and Packout drawer are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eThree STL files\u003c\/strong\u003e: the base, the support lid, and the lid's raised size labels and logo as their own part, so they can print in a second colour\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT IT HOLDS\u003cbr\u003e\n- Metric 6-point deep impact sockets: 9mm through 30mm, every size (22 sockets)\u003cbr\u003e\nEach socket stands upright in the base and passes through its own labeled hole in the support lid.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Organizer) and 48-22-8435 (Compact Organizer), no adapter\u003cbr\u003e\n✔ Milwaukee Packout deep drawer, with the Mountaineer Maker drawer adapter (sold separately)\u003cbr\u003e\nIt has our standard nesting foot, so it sits on our other organizers.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to CHINA-made Sunex 6-point metric deep impact sockets. Taiwan-made Sunex sockets, another depth or another brand may not fit. China-made Sunex sockets do not carry a \"TAIWAN\" stamp; if yours are stamped TAIWAN, message us before buying.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Two pieces: the base is 293 × 193 × 48.5 mm and the support lid 293 × 193 × 10.5 mm (49 mm tall together). Your bed must be at least about 300 × 200 mm. Neither piece fits a 256 × 256 mm bed whole.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print each piece as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003cbr\u003e\n- Two colours, optional: load the labels STL as a part of the lid and give it your second colour. For a one-colour lid, leave it out. The lid snaps into the base.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the \u003ca href=\"\/products\/milwaukee-packout-1-2-drive-deep-impact-socket-organizer-insert-for-sunex-6-point-metric-22-pc\"\u003efinished organizer\u003c\/a\u003e in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67696706748652,"sku":"SUN-006-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/sun-006-dig-01-organizer-render.jpg?v=1792954854"},{"product_id":"milwaukee-packout-1-4-drive-modular-impact-socket-organizer-stl-file-for-gearwrench-84902-6-point-sae-metric-shallow-deep-48-pc","title":"Milwaukee Packout 1\/4\" Drive Modular Impact Socket Organizer STL File for GearWrench 84902 6-Point SAE \u0026 Metric, Shallow \u0026 Deep (48-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our modular Milwaukee Packout organizer for the GearWrench 84902 1\/4\" drive impact set: 6-point SAE and metric, shallow and deep, 48 sockets, every size labeled. An outer frame holds three removable parts (an SAE tray, a metric tray and an accessory rack), so you can lift just the one you need out to the bench. A one-piece version is included too.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, tools, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eFour STL files for the modular organizer\u003c\/strong\u003e, one per printed part: the outer frame, the SAE tray, the metric tray and the accessory rack\u003cbr\u003e\n- \u003cstrong\u003eOne STL file for the one-piece organizer\u003c\/strong\u003e: the same sockets as a single part, with an open bay that takes the same accessory rack\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the frame or the one-piece with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT GOES WHERE\u003cbr\u003e\n- \u003cstrong\u003eSAE tray\u003c\/strong\u003e (20 sockets): 3\/16\"–9\/16\", shallow sockets upright and deep sockets lying flat in labeled troughs\u003cbr\u003e\n- \u003cstrong\u003eMetric tray\u003c\/strong\u003e (28 sockets): 4mm–15mm including the 4.5mm and 5.5mm half sizes, shallow upright and deep lying flat\u003cbr\u003e\n- \u003cstrong\u003eAccessory rack\u003c\/strong\u003e: open rails for your 1\/4\" ratchet and extensions (the 84902 set itself has none)\u003cbr\u003e\nGearWrench sells this range as the 84902 48-piece impact set.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers 48-22-8431 and 48-22-8436\u003cbr\u003e\n✔ Standard tool chest drawers (the organizer is 293 × 193 × 41 mm)\u003cbr\u003e\nWith an adapter or spacer (sold separately): the deep Packout organizers 48-22-8430 and 48-22-8435, and Packout drawers. The frame nests with our other organizers, above and below.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to the exact dimensions of GearWrench 84902 1\/4\" 6-point impact sockets. Sockets from a different brand or a different set may not fit.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The largest part is the frame (or the one-piece), 293 × 193 mm and 41 mm tall; the trays and the accessory rack are 182 mm wide or less. Your bed must be at least about 300 × 200 mm for the frame. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Print each part as it loads, flat side down. No supports needed\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- The size labels, headings and logo are raised, so you can print them in a second colour by painting the label tops with your slicer's colour-painting tool (Creality Print, Bambu Studio and Orca Slicer all have one). Otherwise each part prints in one colour.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67701120303340,"sku":"GRW-003-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/grw-003-dig-01-organizer-render.jpg?v=1791707590"},{"product_id":"klein-modbox-54844mb-drawer-adapter-for-socket-organizer-inserts-4-piece-set-stl-file","title":"Klein MODbox 54844MB Drawer Adapter for Socket Organizer Inserts, 4-Piece Set – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the drawer adapter yourself.\u003c\/strong\u003e This is the 3D print file for our Klein MODbox 54844MB drawer adapter: four pieces that seat two of our standard socket organizer inserts in a Klein MODbox 54844MB compact single drawer, one on each side, held at the base so they don't slide.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizer inserts, sockets and the Klein drawer are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the platform (the drawer-side piece) and the carrier (the organizer-side piece). Print each one twice, one of each for each side of the drawer. The carrier file is already turned upside down, the way it prints\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ The Klein MODbox 54844MB compact single drawer, one adapter set per drawer\u003cbr\u003e\nThe MODbox drawer floor rises into a hump down the middle. On each side, a platform sits on the floor beside the hump and a carrier on top of it catches the organizer's base. Keys on both pieces slide into the drawer's side-wall grooves, and a center bar under each organizer keeps a loaded one from sagging.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: built for the Klein MODbox 54844MB drawer only. It is not designed for other MODbox drawers or toolboxes, or for other drawer systems.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The largest pieces are 322 × 173 × 21 mm (platform) and 303 × 230 × 14 mm (carrier). Your bed must be at least about 325 × 235 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints with no supports: the platform bottom-down, the carrier upside down as the file comes\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished adapter in our shop. Don't have an organizer for your set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67710686429420,"sku":"KLN-ADPT-54844MB-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/kln-adpt-54844mb-dig-01-hero.jpg?v=1792954853"},{"product_id":"milwaukee-packout-1-2-drive-impact-socket-organizer-stl-file-set-gearwrench-89095-6-point-sae-metric-shallow-deep-65-pc","title":"Milwaukee Packout 1\/2\" Drive Impact Socket Organizer STL File Set for GearWrench 89095 6-Point SAE \u0026 Metric, Shallow \u0026 Deep (65-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizers yourself.\u003c\/strong\u003e These are the 3D print files for our GearWrench 89095 organizer set: 1\/2\" drive impact sockets, SAE and metric, shallow, deep and hex bit, 6-point, plus both extensions and the universal joint. 65 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, extensions, universal joint, organizers and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSeven STL files\u003c\/strong\u003e: the deep organizer and its snap-in support lid, the standard organizer, and the storage tray, plus a separate labels file for the deep organizer, the lid and the standard organizer, so the size labels and logo can print in a second colour. The deep organizer holds the deep and hex bit sockets and both extensions; the standard organizer holds the shallow sockets and the universal joint, and sits on the storage tray so the closed Packout lid holds every socket.\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ One Milwaukee Packout 48-22-8430 (Deep Organizer): both organizers side by side, the standard organizer on the storage tray\u003cbr\u003e\n✔ Or two Milwaukee Packout 48-22-8435 (Compact Deep Organizer): the deep organizer in one, the standard organizer on the storage tray in the other\u003cbr\u003e\nBuilt to GearWrench's 89095 1\/2\" impact sockets and accessories. Too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to measured GearWrench 89095 sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Four pieces, each 293 × 193 mm: the deep organizer is 48.5 mm tall, its lid 13.6 mm, the standard organizer 57.5 mm and the storage tray 38.5 mm. Your bed must be at least about 300 × 200 mm. They do \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print every piece upright, as it sits in the box\u003cbr\u003e\n- Designed on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOUR LABELS (optional)\u003cbr\u003e\n- Load each piece together with its labels file as one multi-part object and assign the labels a second filament. The labels sit in place on top of the piece.\u003cbr\u003e\n- For one colour, print the organizer, lid and tray files alone.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67720431042796,"sku":"GRW-004-DIG","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/grw-004-dig-01-hero-render.jpg?v=1791911778"},{"product_id":"milwaukee-packout-3-8-shockwave-deep-impact-socket-organizer-stl-file-49-66-7006-sae-12-pc","title":"Milwaukee Packout 3\/8\" Shockwave Deep Impact Socket Organizer STL File – 49-66-7006 SAE (12-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee SHOCKWAVE organizer insert for the 3\/8\" drive SAE deep impact set 49-66-7006: 12 deep 6-point sockets, 5\/16\" through 1\", every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer) and 48-22-8436 (Compact Low-Profile Organizer)\u003cbr\u003e\nBuilt to Milwaukee's SHOCKWAVE 3\/8\" SAE deep impact sockets, 5\/16\" through 1\". The sockets lie flat in labeled troughs: 5\/16\"–3\/4\" in one row, 13\/16\"–1\" in the other.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: troughs are cut to Milwaukee SHOCKWAVE 3\/8\" SAE deep impact sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 41 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- PETG recommended\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOR LABELS (optional)\u003cbr\u003e\n- The size labels are raised 1.5 mm above the deck. To print them in a second color, use your slicer's paint or color tool on the raised labels. A plain filament change by height would also color the top of the rim.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67834816889068,"sku":"MIL-016-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/mil-016-dig-01-organizer-render.jpg?v=1792600284"},{"product_id":"klein-modbox-54823mb-bottom-drawer-adapter-for-socket-organizer-inserts-6-piece-set-stl-file","title":"Klein MODbox 54823MB Bottom Drawer Adapter for Socket Organizer Inserts, 6-Piece Set – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the drawer adapter yourself.\u003c\/strong\u003e This is the 3D print file for our Klein MODbox 54823MB bottom drawer adapter: two hanging halves and four small support stands that seat two of our slim (low-profile) socket organizer inserts in the bottom drawer of a Klein MODbox 54823MB three-drawer toolbox, one on each side, held at the base so they don't slide.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizer inserts, sockets and the Klein toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eThree STL files\u003c\/strong\u003e: the left half, the right half (a mirror of the left), and the support stand. Print each half once and the stand four times\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ The bottom drawer of the Klein MODbox 54823MB three-drawer toolbox, one adapter set per drawer\u003cbr\u003e\nThe bottom drawer has a tall hump down the middle. Each half hangs from the drawer's side tracks on its outer edge and rests on the hump on its inner edge, giving a level seat that catches the organizer's base. Side lugs and front and rear tabs drop into the drawer's own features, and the four stands slide into the lower side tracks under the frame to keep a loaded organizer from sagging. Our slim organizer inserts fit one per side with the drawer above still closing; there isn't room to stack organizers in this drawer.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: built for the bottom drawer of the Klein MODbox 54823MB only. It does not fit the 54823MB's top or middle drawers, other MODbox boxes or drawers, or other toolbox systems.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Each half is 311 × 206 × 45 mm. Your bed must be at least about 315 × 210 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints with no supports: the halves bottom-down as the files come, the stands on their side (wide face down)\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished adapter in our shop. Don't have an organizer for your set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67857727357164,"sku":"KLN-ADPT-54823MB-LOWER-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/kln-adpt-54823mb-lower-dig-01-hero.jpg?v=1792954853"},{"product_id":"milwaukee-packout-1-2-drive-impact-socket-organizer-stl-file-set-kobalt-80724-6-point-sae-metric-shallow-deep-55-pc","title":"Milwaukee Packout 1\/2\" Drive Impact Socket Organizer STL File Set for Kobalt 80724 6-Point SAE \u0026 Metric, Shallow \u0026 Deep (55-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizers yourself.\u003c\/strong\u003e These are the 3D print files for our Kobalt 80724 organizer set: 1\/2\" drive impact sockets, SAE and metric, shallow and deep, 6-point, plus the extensions, swivels, adapter and flip socket. 55 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, accessories, organizers, rails, clips and the Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSeven STL files\u003c\/strong\u003e: the deep organizer and its snap-in support lid, the standard organizer, and the storage tray, plus a separate labels file for the deep organizer, the lid and the standard organizer, so the size labels and logo can print in a second color. The deep organizer holds the 24 deep sockets and the flip socket; the standard organizer holds the 24 shallow sockets and sits on the storage tray so the closed Packout lid holds every socket.\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eTHE CLIP RAIL\u003cbr\u003e\nThe storage tray has grooves at each end for our \u003ca href=\"\/products\/milwaukee-packout-flexrail-universal-socket-organizer-starter-kit-rotating-rail-system-compatible-tool-organizer-fathers-day-gift\"\u003eFlexRail\u003c\/a\u003e short rail, which holds the extensions, swivels and adapter on twist-lock clips. The rail and clips are not in this download; a rounded cradle in the tray supports the long extensions either way.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ One Milwaukee Packout 48-22-8430 (Deep Organizer): both organizers side by side, the standard organizer on the storage tray\u003cbr\u003e\nBuilt to Kobalt's 80724 1\/2\" impact sockets and accessories. Not for the compact 48-22-8435 (the set needs both bays of the 8430), and too tall for the low-profile organizers (48-22-8431 and 48-22-8436).\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Kobalt 80724 sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Four pieces, each 293 × 193 mm. Your bed must be at least about 300 × 200 mm. They do \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print every piece upright, as it sits in the box\u003cbr\u003e\n- Designed on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOR LABELS (optional)\u003cbr\u003e\n- Load each piece together with its labels file as one multi-part object and assign the labels a second filament. The labels sit in place on top of the piece.\u003cbr\u003e\n- For one color, print the organizer, lid and tray files alone.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the \u003ca href=\"\/products\/milwaukee-packout-1-2-drive-impact-socket-organizer-insert-set-kobalt-80724-6-point-sae-metric-shallow-deep-48-pc\"\u003efinished organizer set\u003c\/a\u003e, with the rail and clips, in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67857730502892,"sku":"KOB-001-DIG","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/kob-001-dig-01-hero-render-deep.jpg?v=1792790550"},{"product_id":"klein-modbox-54823mb-top-and-middle-drawer-adapter-for-socket-organizer-inserts-3-piece-set-stl-file","title":"Klein MODbox 54823MB Top and Middle Drawer Adapter for Socket Organizer Inserts, 3-Piece Set – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the drawer adapter yourself.\u003c\/strong\u003e This is the 3D print file for our Klein MODbox 54823MB top and middle drawer adapter: three flat pieces, a left end, a right end and a center, that seat two of our slim (low-profile) socket organizer inserts side by side in the top or middle drawer of a Klein MODbox 54823MB three-drawer toolbox, held at the base so they don't slide.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizer inserts, sockets and the Klein toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eThree STL files\u003c\/strong\u003e: the left end, the right end (a mirror of the left) and the center. Print each one once\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ The top drawer or the middle drawer of the Klein MODbox 54823MB three-drawer toolbox, one adapter set per drawer\u003cbr\u003e\nThe three pieces lie flat in the drawer's floor bays, with the seams over the drawer's two floor ribs. The ends lock into the drawer's side tracks and the center wedges between the ribs, so the set sits tight and gives each organizer a level seat that catches its base the same way our organizers catch each other when they stack. Two of our slim organizer inserts fit side by side, with room to stack a second slim organizer on each and the drawer still closing.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: built for the top and middle drawers of the Klein MODbox 54823MB only. It does not fit the 54823MB's bottom drawer (we make a separate adapter for that one), other MODbox boxes or drawers, or other toolbox systems.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- Each piece is about 311 × 126 × 20 mm. Your bed must be at least about 315 × 130 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints with no supports, every piece bottom-down as the files come\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished adapter in our shop. Don't have an organizer for your set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67858303058156,"sku":"KLN-ADPT-54823MB-UPPER-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/kln-adpt-54823mb-upper-dig-01-hero.jpg?v=1792954854"},{"product_id":"milwaukee-packout-1-2-drive-deep-impact-socket-organizer-stl-3mf-file-for-harbor-freight-icon-59746-6-point-metric-14-pc","title":"Milwaukee Packout 1\/2\" Drive Deep Impact Socket Organizer STL\/3MF File for Harbor Freight Icon 59746 6-Point Metric (14-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Icon deep impact socket organizer insert: the complete Harbor Freight Icon 59746 1\/2\" drive metric deep impact set, 14 sockets from 10mm to 27mm, 6-point, each lying flat in its own labeled cradle, with an open storage bin across the front.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne 3MF file\u003c\/strong\u003e: the organizer with its base and labels already set up as one two-color object\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the organizer base, and its labels already in place for a second color\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED (Icon 59746)\u003cbr\u003e\n10mm · 11mm · 12mm · 13mm · 14mm · 15mm · 16mm · 17mm · 18mm · 19mm · 21mm · 22mm · 26mm · 27mm\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout low-profile organizers: 48-22-8436 holds one, 48-22-8431 holds two\u003cbr\u003e\n✔ Standard tool chest drawers: drops straight in\u003cbr\u003e\nLying flat, the 26mm and 27mm sockets are bigger across than a low-profile organizer is tall, so they sit in the row under the groove molded into the Packout lid, and the lid still closes flat over the whole set. The organizer nests on the bottom only, so it goes on top of a stack. The 10mm to 15mm have a narrower neck, so each gets a stepped cradle that fits both diameters. Every size is labeled beside its socket.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: cradles are cut to Icon's 1\/2\" metric deep impact sockets, from caliper measurements of the actual set. Icon's SAE deep sockets, standard-length sockets, or deep sockets from another brand may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 36 mm. Your bed must be at least about 300 × 200 mm. It doesn't fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut the organizer to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOR LABELS\u003cbr\u003e\n- \u003cstrong\u003eEasiest:\u003c\/strong\u003e open the 3MF. Base and labels are already one object on two filaments; pick your two colors.\u003cbr\u003e\n- With the STLs: import the base and its labels file together and load them as \u003cstrong\u003eone object with multiple parts\u003c\/strong\u003e, without re-arranging, so every label stays in its place. Give the labels part your second filament.\u003cbr\u003e\n- One color only? Leave both parts on the same filament.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67873990213868,"sku":"ICN-008-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/icn-008-dig-01-metric-organizer-render.jpg?v=1792934949"},{"product_id":"klein-modbox-54500mbx-adapter-for-socket-organizer-inserts-one-piece-stl-file","title":"Klein MODbox 54500MBX Adapter for Socket Organizer Inserts, One-Piece – STL File","description":"\u003cp\u003e\u003cstrong\u003ePrint the adapter yourself.\u003c\/strong\u003e This is the 3D print file for our Klein MODbox 54500MBX adapter: one piece that sits on the box floor, catches the base of one of our standard socket organizer inserts, and holds it centered with the lid closed and latched.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eRequires a minor modification:\u003c\/strong\u003e to use the adapter, remove the small front and rear ribs inside the 54500MBX (four in all, two at each end). They only line up Klein's own bins, and they come off in a few minutes with a flush cutter or utility knife. A printable instruction card is included in the download.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Organizer inserts, sockets and the Klein box are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne STL file\u003c\/strong\u003e: the one-piece adapter, oriented the way it prints\u003cbr\u003e\n- \u003cstrong\u003eA \"Before you install\" card\u003c\/strong\u003e (PDF, 4 x 6 in) showing which four ribs to remove and how\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is too small\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ The Klein MODbox 54500MBX organizer, one adapter per box\u003cbr\u003e\nThe adapter holds the organizer at the same height as the Milwaukee Packout deep organizers (48-22-8430 and 48-22-8435), so a shorter insert takes the same spacer tray it would take in a Packout. It locates on the box's own side bosses and end walls, and a center bar under the organizer keeps a loaded one from sagging.\u003c\/p\u003e\n\n\u003cp\u003eHOW TO PREP THE BOX (ONE TIME)\u003cbr\u003e\nEmpty the box, then find the two small ribs at the front (on the raised housing) and the two on the rear end wall. Cut each one off flush with a flush cutter or a utility knife, cutting away from yourself, and smooth any burrs. Then drop the adapter in and set your organizer on it.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: built for the Klein MODbox 54500MBX organizer only. It is not designed for other MODbox boxes or drawers, or for other toolbox systems.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The adapter is about 313 × 210 mm. Your bed must be at least about 315 × 215 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Prints bottom-down with no supports\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished adapter in our shop. Don't have an organizer for your set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67878349504748,"sku":"KLN-ADPT-54500MBX-DIG","price":5.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/kln-adpt-54500mbx-dig-01-adapter-render.jpg?v=1792944123"},{"product_id":"milwaukee-packout-1-4-3-8-drive-socket-organizer-stl-3mf-file-set-for-gearwrench-80948-12-point-sae-metric-shallow-deep-76-pc","title":"Milwaukee Packout 1\/4\" \u0026 3\/8\" Drive Socket Organizer STL\/3MF File Set for GearWrench 80948 12-Point SAE \u0026 Metric, Shallow \u0026 Deep (76-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizers yourself.\u003c\/strong\u003e These are the 3D print files for our GearWrench 80948 organizer set: 1\/4\" and 3\/8\" drive 12-point sockets, SAE and metric, shallow and deep, plus both ratchets, extensions, universal joints and adapters. 76 pieces, every size labeled.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, ratchets, extensions, organizers and Packout case are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eNine STL files\u003c\/strong\u003e: the 3\/8\" organizer, the 1\/4\" frame and its three trays (tool tray, SAE tray, metric tray), plus a separate labels file for the 3\/8\" organizer and each 1\/4\" tray, so the size labels and logo can print in a second color\u003cbr\u003e\n- \u003cstrong\u003eFour two-color 3MF files\u003c\/strong\u003e: the 3\/8\" organizer and the three 1\/4\" trays, each with body and labels already assigned to two filaments\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8431 (Low-Profile Organizer): both organizers side by side\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8436 (Compact Low-Profile Organizer): one organizer per box\u003cbr\u003e\nBuilt to GearWrench's 80948 1\/4\" and 3\/8\" 12-point sockets and drive tools.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to measured GearWrench 80948 sockets. Other brands may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- The 3\/8\" organizer is one piece, 293 × 193 × 30.3 mm. The 1\/4\" frame is 293 × 193 × 41 mm; its three trays are 182 mm wide and 84, 98.3 and 98.7 mm long. Your bed must be at least about 300 × 200 mm for the organizer and the frame. They do \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print every piece upright, as it sits in the box\u003cbr\u003e\n- Designed on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOR LABELS (optional)\u003cbr\u003e\n- Open a 3MF and it loads with the labels already on a second filament. If your slicer asks: \"scale to mm?\" No; \"load as a single object with multiple parts?\" Yes.\u003cbr\u003e\n- Or load each STL together with its labels file as one multi-part object and assign the labels a second filament. For one color, print the organizer, frame and tray files alone.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer set in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67878380929260,"sku":"GRW-005-DIG","price":25.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/grw-005-dig-01-set-render.jpg?v=1792938572"},{"product_id":"bauer-58511-toolbox-1-2-drive-impact-socket-organizer-stl-file-for-harbor-freight-quinn-58680-6-point-metric-deep-shallow-28-pc","title":"Bauer 58511 Toolbox 1\/2\" Drive Impact Socket Organizer STL File for Harbor Freight Quinn 58680 6-Point Metric Deep \u0026 Shallow (28-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Bauer 58511 organizer insert: all 28 metric impact sockets from the Harbor Freight Quinn 58680 master set, 1\/2\" drive, 6-point, 10mm–22mm plus 24mm, shallow and deep, every size labeled. It stands upright in the Bauer 58511 toolbox, with a slot at each end that slides over the box's wall ribs like the factory divider. Every socket leans back into its own pocket, so gravity holds it in the box, standing on a bench, or lying on its back.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eSTL file\u003c\/strong\u003e: the whole organizer as one piece, already in its print position, with its two print support fins in place\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split a part with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer)\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eTHE SUPPORT FINS\u003cbr\u003e\nThe organizer prints tilted back so every pocket prints straight up. Two thin fins behind the back plate hold it steady on the bed while it prints. They are print supports, not part of the organizer: snap them off after printing. The organizer stands on its own feet without them.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Bauer 58511 toolbox, standing in the box's wall ribs\u003cbr\u003e\nBuilt to the Quinn 58680 set. Quinn's 1\/2\" metric range has no 23mm, so the gap between 22mm and 24mm is the manufacturer's.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to Harbor Freight Quinn 1\/2\" metric impact sockets, and the end slots are made for the Bauer 58511. Other brands, sets and toolboxes may not fit. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece. The organizer is 298 × 263 × 84 mm standing up; in its print position it takes about 298 × 220 mm of bed and 223 mm of height. Your bed must be at least about 300 × 225 mm.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed?\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for cutting a part in Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- Our settings: 0.20 mm layers, 2 walls, 10% infill, supports on from the build plate only (for the carry-handle openings), bridge flow 1.15 and bridge speed 40\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003cbr\u003e\n- Single color as supplied: the size labels are raised, so a filament change or your slicer's paint tool picks them out in a second color\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67881798336748,"sku":"QNN-001-DIG","price":20.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/qnn-001-dig-01-metric-organizer-render.jpg?v=1792949695"},{"product_id":"milwaukee-packout-1-2-drive-shallow-impact-socket-organizer-stl-3mf-file-for-gearwrench-89072-6-point-metric-8mm-36mm-26-pc","title":"Milwaukee Packout 1\/2\" Drive Shallow Impact Socket Organizer STL\/3MF File for GearWrench 89072 6-Point Metric, 8mm–36mm (26-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our GearWrench metric impact socket organizer insert: the 26 metric standard-length sockets of the GearWrench 89072 1\/2\" drive impact set, 8mm to 36mm, 6-point, each standing in its own labeled pocket, in size order with the largest at the front.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer and toolbox are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne 3MF file\u003c\/strong\u003e: the organizer with its body and labels already set up as one two-color object\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the organizer body, and its labels already in place for a second color\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eSIZES COVERED (GearWrench 89072, metric standard)\u003cbr\u003e\n8mm · 9mm · 10mm · 11mm · 12mm · 13mm · 14mm · 15mm · 16mm · 17mm · 18mm · 19mm · 20mm · 21mm · 22mm · 23mm · 24mm · 25mm · 26mm · 27mm · 28mm · 29mm · 30mm · 31mm · 32mm · 36mm\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout deep organizers 48-22-8430 and 48-22-8435, on our 33.5mm spacer tray (sold separately) so the lid holds the sockets in place\u003cbr\u003e\n✔ Standard tool chest drawers: drops straight in\u003cbr\u003e\nThe organizer nests top and bottom, so it stacks with our other organizers and drawer adapters.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to GearWrench's 89072 1\/2\" metric standard impact sockets, from caliper measurements of the actual set. Deep sockets, SAE sockets, or sockets from another set or brand may not seat correctly. Message us before buying if you're unsure.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 58 mm. Your bed must be at least about 300 × 200 mm. It doesn't fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut the organizer to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOR LABELS\u003cbr\u003e\n- \u003cstrong\u003eEasiest:\u003c\/strong\u003e open the 3MF. Body and labels are already one object on two filaments; pick your two colors.\u003cbr\u003e\n- With the STLs: import the body and its labels file together and load them as \u003cstrong\u003eone object with multiple parts\u003c\/strong\u003e, without re-arranging, so every label stays in its place. Give the labels part your second filament.\u003cbr\u003e\n- One color only? Leave both parts on the same filament.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the finished organizer in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67982146633964,"sku":"GRW-009-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/grw-009-dig-01-metric-organizer-render.jpg?v=1793198691"},{"product_id":"milwaukee-packout-1-2-drive-shallow-impact-socket-organizer-stl-3mf-file-for-sunex-china-made-6-point-metric-10mm-36mm-27-pc","title":"Milwaukee Packout 1\/2\" Drive Shallow Impact Socket Organizer STL\/3MF File for Sunex China-Made 6-Point Metric, 10mm–36mm (27-Pc)","description":"\u003cp\u003e\u003cstrong\u003ePrint the organizer yourself.\u003c\/strong\u003e This is the 3D print file for our Milwaukee Packout organizer insert for China-made Sunex 1\/2\" drive shallow impact sockets: 6-point metric, 10mm to 36mm, 27 pieces, every size labeled and nothing skipped, the 31mm included.\u003c\/p\u003e\n\n\u003cp\u003eDIGITAL FILE ONLY\u003cbr\u003e\nYou receive a ZIP download right after purchase. Sockets, organizer, spacer, drawer adapter and Packout are not included, and nothing is shipped.\u003c\/p\u003e\n\n\u003cp\u003eWHAT YOU'LL RECEIVE\u003cbr\u003e\n- \u003cstrong\u003eOne 3MF file\u003c\/strong\u003e: the organizer with its body and labels already set up as one two-color object\u003cbr\u003e\n- \u003cstrong\u003eTwo STL files\u003c\/strong\u003e: the organizer body, and its labels already in place for a second color\u003cbr\u003e\n- \u003cstrong\u003eA Start-here card\u003c\/strong\u003e linking to our \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e: recommended settings, plus how to split the organizer with your slicer's cut tool (Creality Print, Bambu Studio, Orca Slicer) if your bed is smaller than about 300 × 200 mm\u003cbr\u003e\n- \u003cstrong\u003eThe license\u003c\/strong\u003e: the Mountaineer Maker Digital Product License (v1.0) as a PDF\u003c\/p\u003e\n\n\u003cp\u003eWHAT IT HOLDS\u003cbr\u003e\n- Metric 6-point shallow impact sockets: 10mm through 36mm, every size (27 sockets)\u003cbr\u003e\nEvery socket stands upright in its own pocket, with the size labeled on the deck and in the pocket floor.\u003c\/p\u003e\n\n\u003cp\u003eFITS\u003cbr\u003e\n✔ Milwaukee Packout 48-22-8430 (Organizer) and 48-22-8435 (Compact Organizer), with the Mountaineer Maker 37 mm spacer tray under it (sold separately)\u003cbr\u003e\n✔ Milwaukee Packout drawers, with the Mountaineer Maker drawer adapter (sold separately)\u003cbr\u003e\n✔ Standard tool chest drawers: drops straight in\u003cbr\u003e\n✘ Too tall for the low-profile 48-22-8431 and 48-22-8436\u003cbr\u003e\nIt has our standard nesting foot and top, so it stacks and nests with our other organizers.\u003c\/p\u003e\n\n\u003cp\u003e⚠ NOT UNIVERSAL: pockets are cut to CHINA-made Sunex 6-point metric shallow impact sockets. Taiwan-made Sunex sockets, another depth or another brand may not fit. China-made Sunex sockets do not carry a \"TAIWAN\" stamp; if yours are stamped TAIWAN, message us before buying.\u003c\/p\u003e\n\n\u003cp\u003ePRINTER REQUIREMENTS\u003cbr\u003e\n- One piece, 293 × 193 × 54 mm. Your bed must be at least about 300 × 200 mm. It does \u003cstrong\u003enot\u003c\/strong\u003e fit 256 × 256 mm beds in one piece.\u003cbr\u003e\n- \u003cstrong\u003eSmaller bed? Your slicer can cut it to fit.\u003c\/strong\u003e See the step-by-step \u003ca href=\"\/pages\/print-instructions\"\u003eprint instructions\u003c\/a\u003e for Creality Print, Bambu Studio and Orca Slicer.\u003cbr\u003e\n- No supports needed: print it as it loads, flat side down\u003cbr\u003e\n- Designed and tested on a Creality K2 Plus; we print ours in PETG\u003c\/p\u003e\n\n\u003cp\u003eTWO-COLOR LABELS\u003cbr\u003e\n- \u003cstrong\u003eEasiest:\u003c\/strong\u003e open the 3MF. Body and labels are already one object on two filaments; pick your two colors.\u003cbr\u003e\n- With the STLs: import the body and its labels file together and load them as \u003cstrong\u003eone object with multiple parts\u003c\/strong\u003e, without re-arranging, so every label stays in its place. Give the labels part your second filament.\u003cbr\u003e\n- One color only? Leave both parts on the same filament.\u003c\/p\u003e\n\n\u003cp\u003eLICENSE\u003cbr\u003e\nPersonal use under the \u003ca href=\"\/pages\/digital-license\"\u003eMountaineer Maker Digital Product License (v1.0)\u003c\/a\u003e. You may print it for yourself and give prints as personal gifts; selling prints or sharing the file needs a commercial license or written permission.\u003c\/p\u003e\n\n\u003cp\u003ePrefer it printed? We sell the \u003ca href=\"\/products\/milwaukee-packout-1-2-drive-shallow-impact-socket-organizer-insert-for-sunex-6-point-metric-10mm-36mm-27-pc\"\u003efinished organizer\u003c\/a\u003e in our shop. Don't have this exact set? Message us. We build organizers for specific socket sets.\u003c\/p\u003e\n","brand":"Mountaineer Maker","offers":[{"title":"Default Title","offer_id":67983100870892,"sku":"SUN-007-DIG","price":15.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/6250\/0332\/files\/sun-007-dig-01-metric-organizer-render.jpg?v=1793202920"}],"url":"https:\/\/mountaineermaker.com\/collections\/stl-downloads\/brand:milwaukee.oembed","provider":"Mountaineer Maker","version":"1.0","type":"link"}